Betaflight rcgroupsemplois

Hi, I am looking for someone to assist me in developing firmware for modified Mango pi based boards ( which will have barometer, accelerometer, gyroscope ) for flight Controller application for my mini project. The boards are based on Allwinner T113-S3 ,F133A/D1s, V853(new one,not in mango pi family...Allwinner T113-S3 ,F133A/D1s, V853(new one,not in mango pi family). I want these boards firmware to be compatible with Beta flight and INAV (as they have GUI interfaces for programming flight path etc..). Reference code for flight control is available , which is based on STM32 MCU. Note: I will take care of the hardware design. Only software end has to be designed. Betaflight GitHub page: You can check those mango pi boards on:

Hi, I'm looking for a way to upload FC drone blackbox reports as input and the sfw give me a P I D value for roll pitch and yaw that minimize the PID error (by Montecarlo method, fuzzy...) . Samething for filters.. Could someone help me? I attach a report analyzed by PID analyzer and a fc's blackbox report with betaflight firmware

we'd like to build a simple quadcopter, using the betaflight framework. We also need to have a channel outputting PWM. Many "toothpick" quadcopters have small SBUS receivers which are connected to the All In One (AIO) flight controller. These FCs have outputs for 4 motors, but we have not yet managed to get access to an additional channel via the flight controller. One solution would be to use a receiver that outputs both SBUS, and PWM (8 channels say) like the X8R from FrSky, but this requires a larger receiver, adding weight and volume. A better solution may be to figure out how to extract the PWM channel from the AIO FC (2-4S, 12-20A).

...working? Zipray: Simultaneous insertion of rtl8812au and ar9271 on the ground will be stuck in smart synchronization Justin Healey: do you mean for the relay only? or simultaneous use of atheros and Realtek cards? Or both cause smart sync to freeze? Zipray: It doesn't matter with relay, even if you disable smart sync, it will get stuck. Including relay, external WiFi hotspots are not available RCgroups (Khomyakk) My setup looks like this - airpi: raspberry pi 3 model B raspberry pi camera module v.2.1 n.1 ALFA AWUS036ACH 5.8Ghz - groundpi: raspberry pi 3 model B HDMI monitor 1280x800 pixel n.1 ALFA AWUS036ACH 5.8Ghz - relaypi: raspberry pi 3 model B n.2 ALFA AWUS036ACH 5.8Ghz P In order for the project to be accepted: The fix should

...controller utilizing an STM32F7*** microcontroller with a pinout compatible with a betaflight unified target (specifying the appropriate pinout for the firmware betaflight configurator) 2) 4-in-1 ESC capable of carrying minimum 40A per brushless motor 3) Radio receiver operating at 2.4GHz with dual antenna receptacles and can utilize either i-bus or s-bus protocols 4) Video transmitter capable of operating at 5.8GHz with configurable frequency. This should be capable of communicating with the flight controller via applicable communication protocol (unknown to me). Essentially, I should be able to program the video transmission frequency, on-screen-display (OSD), and any other settings through the betaflight configurator. Each of these functions already exist in ...

Design a drone that can be flashed with Betaflight. All inclusive design with flight controller and ESC. Able to handle 4S / 30A. Peripherals TBC.

...working? Zipray: Simultaneous insertion of rtl8812au and ar9271 on the ground will be stuck in smart synchronization Justin Healey: do you mean for the relay only? or simultaneous use of atheros and Realtek cards? Or both cause smart sync to freeze? Zipray: It doesn't matter with relay, even if you disable smart sync, it will get stuck. Including relay, external WiFi hotspots are not available RCgroups (Khomyakk) My setup looks like this - airpi: raspberry pi 3 model B raspberry pi camera module v.2.1 n.1 ALFA AWUS036ACH 5.8Ghz - groundpi: raspberry pi 3 model B HDMI monitor 1280x800 pixel n.1 ALFA AWUS036ACH 5.8Ghz - relaypi: raspberry pi 3 model B n.2 ALFA AWUS036ACH 5.8Ghz P In order for the project to be accepted: The fix should

I need an arduino program that controls the pitch and roll of a fc in cleanflight or betaflight on bases at distances obtained from ultrasound, in order to avoid obstacles

Necesito un programa en arduino que controle el pitch y el roll de una fc en cleanflight o betaflight en bases a distancias obtenidas de ultrasonido, con el objetivo de evitar obstáculos

Im in the process of designing an RC Field charge box. I Would like to use the Raspberry Pi 3 B to run the following 4 programs. Betaflight Configurator Butterflight Configurator BLHeli Configurator Need someone to Programme/Compile the programmes to run the GUI on the Raspberry Pi 3 B and send me the documented process so i can repeat for any updated versions of the software.

Betaflight and Butterflight Model Aircraft Flight controller firmware code is available on GitHub. I would like the following modifications done to the code with flight controller hardware targets of: PyrodroneF4 (Betaflight) OmnibusF4SD (Betaflight) HelioRCSpring (Butterflight code) The modifications are: Flight Path Vector The flight path vector will show the direction that the vehicle (quad) is moving as a circle and crosshair symbol. Examples: 1. When the quad is ascending the FPV will show a vertically displaced circle. 2. When the quad is turning right, the FPV will show a right displaced circle. 3. If the quad is flying level with no climbs, descents or turns, the FPV will be level. 4. If the quad has a left yaw but is flying straight ahead, t...

...very successful and very high traffic website see This could be one to use for stimulation for what I want. The site will generate revenue from advertisers so you also need to know how I can manage all this. See I have a VPS server runnings Parallels to host site. Note that rcgroups uses vBulletin , However I am not fussed about what Forum software is chosen, so long as the user experience is perfect - hence you should know about Forums if you are interested in this project. Any purchases of licenses (e.g. vBulletin) will be paid for outside of the successful freelancers payment. The budget can be negotiated for additional work as required