Fermé

Air Hockey Table electronics and coding

Air hockey table electronics and coding: budget £75

I am in the middle of creating an air hockey table and I need someone to help me with the electronics and coding for the lights, scoring and sound systems (note I am in the UK, so want this to work with UK mains power). I am fine when it comes to the woodwork, but I will need lots of help when it comes to the electronics in terms of what to buy, and how to wire it together, and ALL coding. I am on a budget; so the more you can save me in electronics purchases the more I can pay you for your setup help and coding skills!

Plan – There will be a button to start the game, this will start the power to the air blower, and will play a short clip of music (which I’d like to be able to change from time to time) before the countdown timer then starts and the game begins. Ideally - this will also act as a reset button

At each end of the table behind the goals where the players stand I would like to have a 32 x 32 RGB LED matrix. This will show the current the score in the top half of the display. The score will be activated by an IR sensor at either end inside the goal’s, which will register when the puck passes through. At the bottom of the matrix will be the game countdown timer.

The matrix will also show a graphic at the start, when a team scores (the graphic will be displayed in that teams color), and at the end when we have a winner or tie.

Every game can be won in 2 ways… After a 5 minute countdown the team with the highest score wins OR first to 10 goals… so this will need to be thought about when you do the coding. The scores within the matrix will only show a large single digit on either side -> once a player gets to 9 and scores there will be a ‘winner’ graphic shown on the screen rather than a 10 (this is simply so that we can keep the scores big without wasting space with an extra digit on each side)

Around the edges of the table there will be LED’s which are split into 2 halves, the red team and the blue team. Each half will be illuminated throughout the game in the teams color, however when the blue team score I would like the whole table (including the red end) to flash blue, when the red team score I would like the whole table (including the blue end) to flash red.

Finally I want to add sounds to the table…! This will consist of a short sound in the begging when the game starts, like a traditional organ sound from an ice hockey match, then as a team scores I would like to have a selection of around 10-20 different sound clips of which 1 will play at random. Finally there will be a sound marking the end of the game which will either say the winning team is the blue team, the red team or if its a tie. I would like to be able to update the sound clips as time goes by too… maybe I can store these on a USB memory stick which I can update and plug back into the table as and when I want to update the files?

At the end of every game after the final graphic and sound is played all the lights, sounds and power to the air blower will need to be coded to stop automatically until the on/reset button is re-pressed.

Once I have my winning applicant I will be able to supply dimensions, sketches, budget for electronics etc, and answer any questions.

To summarize so that you can work out your time and your quote your role will be…

• To tell me what to order and where from (ideally parts come from the UK)

• To create all the coding for the system you choose as best – be it raspberry pi/arduino or similar to make my machine do as I want it to in the brief above

• To create really cool, exciting graphics for the start, the goals, and outcome of the game making the most of having the 32 x 32 matrix and RGB strips around the table

• To give me very simple and well-written step-by-step instructions with diagrams of how I need to wire everything together correctly, load the code and test

• To offer support for my stupid questions which I will no doubt have along the way as I am putting this all together!

• And to help with coding changes and adjustments when there are issues in testing or slight changes I want to tweak with timings, sound activation, flashes, graphics etc

This project for me is just for fun, I am not starting an air hockey table business, so please apply if you are looking to have some fun yourself and test your coding and electronics skills while making yourself a little cash along the way ☺

Compétences : Codage, Electronique, Programmation, Architecture Logicielle, Développement de logiciel

Voir plus : hockey air 3d model free, coding join table, programming electronics, projects programming electronics, programmer fixed pay, fixed pay job usa, programming huffman coding, matlab programming electronics, required review electronics, outsourcing programming electronics, additional fixed pay, simple programming addition coding, coding pivot table excel open xml , graphic design budget report architecture project, programming electronics project indonesia

Concernant l'employeur :
( 10 commentaires ) Bath, United Kingdom

N° du projet : #12725398

19 freelance ont fait une offre moyenne de 275 £ pour ce travail

555 £ GBP en 10 jours
(16 Commentaires)
5.3
315 £ GBP en 10 jours
(18 Commentaires)
5.1
277 £ GBP en 15 jours
(5 Commentaires)
4.6
pranavsharma2504

Fun was exactly what I was looking for, TBH! Hi, I am Pranav, from India. I see that you have already done your homework here relating to what parts to use, and how they interact with them. I would suggest you Plus

150 £ GBP en 3 jours
(10 Commentaires)
4.5
ahmad5857

Hi sir, We have read your project and offer you our solution on this. If you agree on our rates than we are waiting for your prompt message. We assure you the quality of service through various checks that ar Plus

230 £ GBP en 3 jours
(24 Commentaires)
5.1
ThinkDone1

Hi! We are interested in your project and having good experience in similar project that we already built. If you like we will show our work. You may see our profile for satisfaction. We have some question regarding y Plus

150 £ GBP en 3 jours
(7 Commentaires)
4.3
goldsea808

[url removed, login to view] [url removed, login to view] [url removed, login to view] ================================================================ Hello,how ar Plus

200 £ GBP en 3 jours
(2 Commentaires)
4.0
waleedibrahim92

Hey I am an expert embedded software engineer. I am very interested in this project. I can help you in your design as I have an available lab that contains most of components that you will need. I believe that I will Plus

160 £ GBP en 15 jours
(19 Commentaires)
4.0
gold2star

HI, dear employer! I am a expert in android development and engineering. I can satisfy your requirement 100% perfectly. Once you provide me what is purpose your project i will design and implement it on high level. Plus

555 £ GBP en 10 jours
(6 Commentaires)
3.6
LeoTheFreelancer

More than 10 years’ experience in Design (R&D), Development (Software) and Project, I am a freelance Consultant/Senior Engineering Business Manager with a team of freelancing/contract/subcontract professionals from all Plus

250 £ GBP en 30 jours
(5 Commentaires)
3.5
ahsandilawarr11

i am Assistant Technical manager of Sublime Enterprise . i have 5 year experience to work on microcontroller, PLC ,arduino e.t.c , i also design lots of industrial product . Design Pakistan's 1st RFID debit card syst Plus

150 £ GBP en 3 jours
(4 Commentaires)
3.0
btobwork

We have 12 Years Experienced in PHP, HTML, CSS, MySQL, Wordpress, Apache, Server .Net ( C# and Vb.Net ) Android & IOS etc am really good at fixing errors and bugs. I always think outside the box to provide the best Plus

250 £ GBP en 10 jours
(1 Commentaire)
2.4
555 £ GBP en 10 jours
(2 Commentaires)
1.9
Rajesh088

Dear Client, Hope you doing well. Thank you for providing me an opportunity to showcase my expertise to you. I have gone through your requirement and as per my previous work experience i am ready to start work Plus

277 £ GBP en 10 jours
(2 Commentaires)
2.3
cwiclk

Dear Sir, I have completed my [url removed, login to view] in computer science and have 10+ years experience in IT industry. Please refer my LinkedIn profile for more information. [url removed, login to view] Plus

250 £ GBP en 10 jours
(0 Commentaires)
2.0
Craal

Hello I'm Alejandro Cruz from Venezuela. I'm Electronic Engineer and i worked with raspberry pi, arduino, PIC and freescale microcontroller. I've developed in python and C. My grade thesis was about to implement a data Plus

255 £ GBP en 10 jours
(0 Commentaires)
0.0
yehudaberkovitz

Hi there, Interesting project you have, not technology challenge, but many parts and interfaces. I can do that and it is intersting for me, it will take at least week work to integrate all te part and build the pro Plus

277 £ GBP en 3 jours
(0 Commentaires)
0.0
webdevvn

Hello, i very interested in your project please check my portfolio : [url removed, login to view] [url removed, login to view] https Plus

150 £ GBP en 10 jours
(0 Commentaires)
0.0
kjbrad15kjbrad

Recently retired electric engineer in the US and also hokey player for 30 years! I have many raspberry pi projects to my credit as well as quite a few arduinos of all sorts. You are sensitive to costs as you should be Plus

222 £ GBP en 5 jours
(0 Commentaires)
0.0