Fermé

Android App using XAMARIN

1. There are 3 levels of operators handling the same android device (honeywell scanPal EDA50). They are : 1. Cleaner, 2) Performer 3) Verifier

A machine will have bar code (2D) stuck at various points on it.

Cleaner will scan a barcode to indicate start of clean operation and scan an barcode to indicate stop of clean operation. Between both scans, he will do the cleaning (manual). The interval between start and stop should be verified against prefixed and stored [login to view URL] Interval in a Table . If the stop scan is done less than the specified interval , error has to be raised (and logged into table)

After the cleaning, PERFORMER will come in. He will use the device to go to performer screen and start performing

Again, there will be 20 - 30 barcodes for performing operation. Each barcode will be numbered sequentially from 0 - 30

Performer first Scans 0 and starts cleaning operation. Again the min. Required Interval for scan @ 0 to Scan @ 1 to be checked as above.

But in this case, the check will be between 0 - 1, 1 - 2, 2 -3 and so on …. 28 -29, 29 -30

Finally Verifier comes and verifies.

There is no min. Required Interval specification for verifier. But he has to scan 0, 1, 2, … 30.

For each 0 -1, 1 - 2, …. 29 - 30, he has to capture an image and upload. The image has be named and uploaded to the PC. The image name can be : for eg. isequenceNo .This I have mentioned in the DB Design Doc.

The device has SDK provided by Honeywell for Barcode Scan Engine interface.

All master data will reside in a PC . Device will connect to PC over Wifi (and LAN).

Whether the Master Data should reside as a replicate SQLITE locally on DEVICE ? You decide on this

Each scan result should go to the PC as : Operator Category (Cleaner, Performer, Verifier), Operator ID(scanned by operator before task commencement) , Location ID (start , stop or 0,1,2,…. 30) , time stamp (scan time) and PassFail Result

If all operations are successfully completed, the Machine will be allowed to switch on. this is done with a PLC interface.

Android device can use modbus to interface with PLC

OR :

Android device can send a MQTT message to PC (having MQTT Broker) and PC will send message to PLC

This is the requirement in short.

Points to consider :

1. Connectivity : This is a mobile device on Battery. So it will go into sleep mode. As such connection to MQTT Broker (or Modbus TCP) should be initiated by the User.

For eg: The user should start the application, then login in (by scanning his ID Card) and then Press a button to Connect, only then his screen should open up

For eg :

if Cleaner starts the App, then First a screen (common screen for cleaner, performer and verifier) called SignOn Screen will show

Here the person selects Role (Cleaner / Performer / Verifier ) using some sort of check boxes or dropdown or buttons

Then he scans his ID Card

Then presses - NEXT

Based on this this process, we will show one of the next 3 screens viz: Cleaner Screen, Performer Screen or Verifier Screen

At the same time, we will check for connectivity in the back end.

If connection is ok, we just proceed, else we will alert the user.

In the back end, we will store the data and then forward to the PC

When there is no connection, then the machine can not be started

Challenges :

1. MQTT / Modbus (You can also plan a work around like updating the PC using a WEBSERVICE and PC will send the command to the PLC

2. Android Barcode Scanning (There is an SDK already given by honeywell with an example code too)

3. We can consider storing Master data from PC into the device as SQLITE . Then it is necessary to find if this data has changed at the PC end and update the same.

Compétences : Android, Programmation C#, Mobile App Development, Xamarin

en voir plus : android app using camera, android app using cocos2d, android app using json, xamarin tutorial visual studio 2017, xamarin android project, xamarin studio, xamarin android, xamarin android tutorial pdf, xamarin forms tutorial, xamarin native, xamarin forms, android app using sql, send data android app using tcp connection, android app using bluetooth controlling robot, android app using tesseract, android app using gps, ocr android app using tesseract, android app using wowza, android app using cameras, android app using

Concernant l'employeur :
( 0 commentaires ) Chennai, India

Nº du projet : #18998483

5 freelance font une offre moyenne de ₹43611 pour ce travail

jastp

Hi there! I've read the details you mentioned and I'm interested in working on this app! If you give us your few minutes for the chat then we can discuss some important points about project to go ahead further with Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% INR en 20 jours
(300 Commentaires)
9.1
maanyait

Hello, Can you please share some detail about the work so that we can go through with it estimate . We are good in Xamarin Forms , i am working on Xamarin from last 3 year during these period i understood inside Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% INR en 10 jours
(6 Commentaires)
4.3
vik2570singh

Hi there, I read your requirements that you are looking for I am very confident enough to complete your task with quality and within the time limit and cost effective. Hoping for a positive response Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% INR en 10 jours
(7 Commentaires)
2.6
bencornett272

Hi !! Nice to E-meet you We are a talented Android , iOS , game, and web service developers with 5 years of experience. we work with a network of other specialists who we use to solve specific issues – so you, the clie Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% INR en 10 jours
(0 Commentaires)
0.0
%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% INR en 10 jours
(0 Commentaires)
0.0