I require FEA testing done on some CAD diagrams. I can provide these diagrams for review if requested.
These diagrams represent some front-end suspension components for a passenger vehicle. Specifically wheel spindles and upper/lower control arms.
Testing specifically to meet VSB14 requirements - so would prefer to work with someone that has experience in this area and Australian guidelines.
Throughout Australia, we are to abide by the rules set out on VSB14. for modified vehicles
While named as guidelines, they are legislated in the state of Victoria. To this end, various load cases are specified on anything other than OE suspension and steering systems, and proof of compliance may be obtained via physical testing or FEA.
The primary concern would be the strength of the stub axle/upright, and the lower control arm. To a lesser extent the upper control arm.
3 COMPONENT STRESS LEVELS
The stress levels of any production component in the suspension system must not be increased
over that at which it has been demonstrated to be capable of satisfactory operation.
Stress analysis should be carried out for modified or specially fabricated components and the
following load conditions are suggested as a guide:
• bump loads: 4g vertical;
• rut loads: 1g vertical combined with 0.6g lateral; and
• skid loads: 2g vertical combined with 1.2g skid (longitudinal).
Overturning loads: 2g vertical combined with 2.5g overturning; where g is the static load at the
tyre contact patch when the vehicle is stationary. The stress levels that are acceptable under
these conditions will depend on the materials and the number of times in the life of the vehicle
that the loads can be expected to occur. Other factors which can affect suspension loads and
should be considered are:
• rim offset;
• combination of braking at lock while striking an obstacle;
• steering scrub radius; and
• the effect of steering system loads on the suspension components.
More info here:
[login to view URL]
20 freelance font une offre moyenne de $1145 pour ce travail
Client want to make a FEA for front-end suspension components of a passenger vehicle Target: Specify VSB14 requirements Relevant Skills and Experience FEA, experience in real vehicle, have design, simulate and build p Plus
Hello I am an expert in mechanical engineering and computation mechanics. I have many experiences in FEA for engineering structures. I will provide all details including stress level and safety, kinetic behaviour. Plus
Hello there, Greetings!!! I am a postgraduate CAD/CAM engineer with high proficiency in Ansys for Finite Element Analysis. I have working experience with the following modules: 1. Static Structural 2. Transie Plus
I am a Mechanical Engineer with a masters degree in solid mechanics and a product optimization specialist by profession. I have experience in digital validation using FEA, Matlab,3D Modelling, CAD/CAM, ATOCAD, CFD, CAT Plus
Dear. I am a professional in FEA. I am a professional in structural mechanics. I am sure I can do it. We can discuss about details via chat. I wait for you now. Thanks.
Hi Dear, I majored in mechanics and have the qualification of Master of Mechanics. And I have been solving the mechanical problems for seven years and has good experience and ability. In particular, I have a good ex Plus
Hello, i have read the details provided..please contact me to discuss more on the project deadline and some other few things
Hi I have been working on automotive structural engineering simulations for past 4 years and also worked on load cases for passenger and bus segment. I have gone through your requirements and I am interested in worki Plus
Dear I am a experienced FEA expert and know very well about FEA from CAD diagram. I checked the project description in detail. Please message so that we can progress the project. Hoping your kind reply... Sincerely
I am interested in working on your project. I am a mechanical engineer and I have experience in design and calculation FEA of parts or mechanisms. I wait for your contact to chat more in detail about the project and Plus
Hello, I am an aerospace engineer. I have experience in FEA and I carried out several studies on different softwares. I can make the study on ANSYS or FEmap. I have experience in Abaqus, too. I am interested in this p Plus
Hi , I am good at FE background., both in theory and simulation. Have masters in mech engineering and having hands on and mentoring exposure in abaqus
Hello, dear! I am interested in your project. I have extensive experience in finite element analysis using ANSYS and ANSYS WB. As a developer with rich experience, I am confident about your project. I will provide Plus
I'm mechanical engineer and I want to work with you on your project because I want to work on such kind of project which is really challenging and that project is really cool so let's work together... Relevant Skills Plus
i am specialized in Mechanical Engineering (Product Design, Prototyping services), Electro mechanical Product design, Electromagnetic Simulation inside Solidworks and Graphic Design services. Please contact me to d Plus
Hello, thanks for posting this project. I've previously worked on suspension and component design as well as optimized weight for several components for automotive application. I'll like to work on your project. You c Plus
Hello, dear. I have experiences in FEM fields. I have looked your description and fixed files for your project. I will work as following Australian guideline. I will provide good results in short time. We can disc Plus