En cours

0-24 VDC power supply board design

This project consists of providing a board design and component list for a circuit board which will provide variable DC power to a device. Part numbers of components must be specified for:

1. A connector which mounts to the board which mates to the 24 volt 1 amp power supply specified by Digikey part number T1073-P5P-ND. Please specify a part which is in stock at one of the major electronics retailers such as digikey, mouser, allied or newark

2. A potentiometer with a thumb wheel in the range of 10-15 mm in diameter which is large enough and mechanically robust enough to act as the main control for the power. Again, select a part which is in stock at a major retailer and give part number. The selection of value is up to the designer. The thumb wheel should be in the plane of the board, so that the axis of rotation is perpendicular to the board. The location of the pot should be on the edge of the board so that it can stick out the side of the final artifact and act as a user power control.

3. Whatever other components, presumably a regulator and capacitors, which are required to regulate voltage from 0 V up to the maximum of 24 V available from the supply, with up to the full 1 A of current.

4. If the potentiometer can have a position at one end of rotation where it "clicks" into an off state that is ideal, but if that is not possible, also specify a switch which can stick off the edge of the board for on/off switching. I envision this as a latching rocker switch which is off the opposite side of the board as the pot.

Completion of the project will include generally readable board files which are suitable for submission to a board fabrication house as well as part numbers for the above components. Suggestions for improvement are welcome if you see a way to improve some aspect of this project. File format for circuit board should ideally be compatible with Eagle circuit board design software.

Circuit board should ideally be 24 mm by 24 to 40 mm, the smaller the better, but this is flexible. Corners should have clearance holes for #4 screws far enough in from the corners to be mechanically robust. Output should be a pair of plated holes which can be soldered to.

Thank you.

Compétences : Génie Électrique, Electronique, Ingénierie

Voir plus : design supply, power supply board design, volt power supply, electronics board design, power supply circuit, wheel well, the design pot, supply one, software design components, software component design, robust design, power up 2, power part 2, opposite of maximum, number board design, newark electronics, mouser electronics, in design software, engineering design software, designer electronics, dc design house, dc design, components design, component board, completion by design

Concernant l'employeur :
( 8 commentaires ) Boulder, United States

N° du projet : #1062051

Décerné à :

JJdatajobs

Hello 'lafespietz', Please read my PM. Thank you very much. With regards, JJdatajobs.

55 $ USD en 2 jours
(6 Commentaires)
3.1

7 freelance ont fait une offre moyenne de 126 $ pour ce travail

RfPhD

check ur PM plz

199 $ USD en 10 jours
(22 Commentaires)
5.4
MIKY4227

Design completed in Altium, schematic, layout, Bill of Materials with digikey numbers , Gerbers.

200 $ USD en 5 jours
(14 Commentaires)
4.8
pgmr108

Design completed in PADS suite, schematic, layout, Bill of Materials, Gerbers. Please see PMB

200 $ USD en 7 jours
(4 Commentaires)
3.5
Sollec

Please check PMB

30 $ USD en 50 jours
(1 Commentaire)
1.4
bkalaska

I am a retired electrical engineer, have done this before. Be glad to help.

200 $ USD en 14 jours
(0 Commentaires)
0.0
samran37

Hi, Please check pm. Regards.

40 $ USD en 2 jours
(0 Commentaires)
0.0
piezoengineer

please see PMB

160 $ USD en 2 jours
(0 Commentaires)
0.0