En cours

Ansys Workbench

This is more of help on using ANSYS workbench 12.1. I have created two ANSYS project files representing my problem of study. The problem is a cylindrical shaped part consisting of three different bodies. One of these bodies is made up of Piezo material. The problem is symmetric for now. Therefore I modeled only quarter the geometry.

I tried to input the piezo command lines (piezo dielect and stress). However, it does not work (2D layer workbench project) or it works but not properly (3d-quart workbench project).

Tasks:

1) How to input piezo material properties properly? How to align them with the correct directions? How to change polarization if desired? (I have placed some commands under the piezo body as to change element type)

2) How to use the model as an actuator? (Apply electric-volt and receive mechanical-stress/strain) What are the exact additional command lines (I have placed some command lines)?

3)How to use the model as a sensor? (Apply mechanical-stress/strain and receive electric-volt) What are the exact additional command lines?

4) How measure radial stress, shear stress on curved surfaces (r-theta shear stresses)

I am open for suggestions. I prefer use of ANSYS a combination of work bench and command lines. However, I am open to suggestions. This can be done by Ansys APDL.

The model:
A cylindrical composite shaped part. The composite cylinder (part) is made up of more than one body (each is cylindrical). Let's say we have a cylinder made up of different materials each layer is cylindrical shaped. The core layer is made up of steel and it is cylinder with radius=r0. A piezo layer covers this steel core. The piezo layer is a hollow cylinder surrounding the core and has a radius of r=r1 and of course inner radius r0. A third layer that cover the piezo. Again this layer is a hollow cylinder with both the piezo and core filling it. This layer has a radius r2 and of course an inner radius of r1.

The problem:
This is a forced vibration problem. I will be appling different loads and/or volt with different frequencies.
The piezoelectric layer will act as an actuator or sensor.
The cylinder will be fixed at its axis (center). Fixed displacement at axis.

The analysis:
Measure radial stress, shear stress on curved surfaces (r-theta shear stresses)

Initial attempts:
I have created two ANSYS project files representing my problem of study. The problem is a cylindrical shaped part consisting of three different bodies. One of these bodies is made up of Piezo material. The problem is symmetric for now. Therefore I modeled only quarter the geometry.

I tried to input the piezo command lines (piezo dielect and stress). However, it does not work (2D layer workbench project) or it works but not properly (3d-quart workbench project).
Tasks:

1) How to input piezo material properties properly? How to align them with the correct directions? How to change polarization if desired? (I have placed some commands under the piezo body as to change element type)

2) How to use the model as an actuator? (Apply electric-volt and receive mechanical-stress/strain) What are the exact additional command lines (I have placed some command lines)?

3)How to use the model as a sensor? (Apply mechanical-stress/strain and receive electric-volt) What are the exact additional command lines?

4) How to measure radial stress, shear stress on curved surfaces (r-theta shear stresses)


Although on the surface the project might seem complicated (as it is an on going work) however once you thoroughly review the attached zip files, you will find the following:
The solid models have been already provided.
The APDL command lines "to define piezoelectric elements and their dielect properties also actuator and sensor commands"are added although suppressed
The results are included.

All that is needed is an ANSYS experienced professional to review, suggest, guide and make necessary changes. On the other hand evenif I have not provided all of the above, For a real expert the project is really very simple and easy

Compétences : CAD/CAM, Ingénierie, Analyse d'éléments finis, Génie Mécanique

Voir plus : piezo ansys workbench, ansys piezo, workbench mechanical commands, piezo actuator ansys, change material ansys workbench, ansys workbench piezo actuator, stress strain element ansys workbench, ansys workbench quarter, material polarization ansys, input properties ansys workbench, change element properties workbench ansys, ansys workbench piezo model, works 3d model, workbench 3d model, what is a 2d model, using geometry, quarter 3d model, problem geometry, lines of geometry, lines geometry, geometry lines, geometry and lines, geometry 2, element 3d model, electric 3d model

Concernant l'employeur :
( 105 commentaires ) Orlando, Canada

N° du projet : #1079328

Décerné à :

acortigiano

Hi! MSME and master of AnSys, please check your PMB. Regards!

100 $ CAD en 3 jours
(11 Commentaires)
4.9

7 freelance ont fait une offre moyenne de 376 $ pour ce travail

bchandra1955

Hi I have used ANSYS with my team , see attachment Brajesh

500 $ CAD en 30 jours
(74 Commentaires)
5.9
geobabu

Hi, Please check the PMB. Regards, Geo

30 $ CAD en 10 jours
(2 Commentaires)
4.3
giridharibehera

Dear sir please provide the details of your work.

1200 $ CAD en 7 jours
(0 Commentaires)
0.0
basra410a

name is enough

400 $ CAD en 7 jours
(0 Commentaires)
0.0
NucleonENG

Expert in Ansys. See PMB.

300 $ CAD en 20 jours
(0 Commentaires)
3.8
AbhaBrajesh1956

I can do the needful for you See INBOX abha

100 $ CAD en 15 jours
(1 Commentaire)
0.0