
Completed
Posted
Paid on delivery
I want a compact, standalone countdown timer that anyone can set for up to 60 minutes, on seconds level and easily read on a 7-segment LCD screen. Once the count reaches zero the unit must emit three clear, evenly-spaced beeps, then stop automatically. Key requirements • Hardware is fully self-contained; no external controller or larger system will be available. • Display: 7-segment LCD, bright enough for indoor daylight viewing. • Maximum duration: 1 hour, adjustable in whole-minute and second level. • Audible alert: exactly three beeps at timeout, each about one second apart, loud enough to notice in a small room. • Intuitive buttons or rotary knob to set, start and reset. • Runs on standard batteries (coin cell). Power draw should allow several months of occasional use. Deliverables 1. Schematic, PCB layout (KiCad or Eagle), and complete BOM. 2. Microcontroller firmware source (Arduino-compatible or bare-metal C) with build instructions. 3. Brief user manual plus assembly guide so the unit can be reproduced or handed to a manufacturer. 4. Demonstration video or clear photos proving the prototype counts down and triggers the triple-beep alert. Acceptance criteria • Accurate timing (±1 s over the full hour). • Display remains readable throughout the countdown. • Beeper sequence meets the 3-beep spec without extra tones. Feel free to suggest component substitutions if they simplify sourcing or extend battery life, as long as the core functionality above remains intact.
Project ID: 40759616
34 proposals
Remote project
Active 6 days ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs

Hi, I can design and develop your compact countdown timer, including the KiCad schematic, PCB layout, low-power firmware, and complete BOM. I’ll ensure accurate timing, a clear 7-segment LCD display, intuitive controls, and exactly three beeps at timeout. I’ll also provide assembly instructions and test the prototype to verify it meets your requirements.
€100 EUR in 2 days
4.0
4.0
34 freelancers are bidding on average €164 EUR for this job

Hi, I am an embedded systems engineer with over 16 years of experience. I have extensive experience with low-power electronics, LCD interfaces and embedded firmware, taking products from concept through prototype testing and production preparation. I can design your standalone timer with intuitive controls, minute-and-second adjustment up to 60 minutes, and exactly three evenly spaced beeps followed by an automatic stop. I would confirm the LCD and beeper choices early so daylight readability and alert volume work within the coin-cell power budget. I will provide the schematic, KiCad PCB layout and complete BOM, together with firmware source, build instructions, and clear user and assembly guides. I will build and test a prototype for the ±1-second accuracy over a full hour, display readability and triple-beep sequence, and provide demonstration photos or a video. Do you have a preferred enclosure size, and would you prefer buttons or a rotary knob? My bid covers design, firmware, prototype assembly and validation; fabrication, components and shipping would be charged separately at cost. The 14-day estimate depends on prototype parts and PCB availability. Please contact me to discuss details.
€250 EUR in 14 days
7.7
7.7

Hi, The main challenge here is balancing accurate timing, a readable display, audible alerts, and several months of battery life. I'd approach this with a low-power microcontroller, a dedicated timing source, and an LCD driver suited to battery operation. The firmware would handle minute/second adjustments, start/reset controls, and exactly three timed beeps without additional sounds. I'd structure the deliverables around a KiCad schematic, PCB layout, BOM, firmware, and assembly documentation, with timing and power consumption verified before finalizing the design. One important question: Is a coin cell mandatory, or would you consider AAA batteries? The display brightness and beeper volume could make a coin cell impractical. Also, do you need a physically assembled and tested prototype, or would design files and firmware be sufficient initially? Adnan
€140 EUR in 1 day
5.6
5.6

Hello, I understand you need a compact, standalone countdown timer with a 7-segment LCD, second-level adjustment up to 60 minutes, and exactly three audible beeps at timeout, all powered by batteries with minimal power consumption. With 4 years of experience in electronics and embedded systems, I can handle the schematic, PCB design, firmware development in C, component selection, and manufacturing documentation. I’ll focus on low-power operation, accurate timing, intuitive controls, and a compact, manufacturable design. I can also include a custom mechanical enclosure at no extra cost. Let’s discuss the requirements and choose the best components for reliable performance and long battery life.
€145 EUR in 7 days
5.6
5.6

Hi there, The main challenge is delivering a self-contained, battery-powered countdown timer that remains readable, keeps timing within ±1 second over an hour, and produces exactly three evenly spaced beeps without unnecessary standby drain. I have strong hands-on experience with C Programming, Electronics, and Programming, and have solved similar problems involving embedded firmware timing, low-power hardware, and microcontroller-driven displays. My approach would be to: * Review the required operating behavior, battery constraints, display options, controls, and enclosure assumptions. * Identify the root design constraints and determine what can be reused versus what needs to be changed. * Implement a clean, maintainable solution using an Arduino-compatible or bare-metal C microcontroller, KiCad schematic/PCB design, and a complete BOM. * Test edge cases, reliability, timing accuracy, battery usage, display readability, button handling, and the exact three-beep sequence. * Deploy or integrate the fix without disrupting the existing system, including build instructions, assembly guidance, user documentation, and prototype demonstration evidence. For ±1-second accuracy across 60 minutes, I would use a calibrated crystal or suitably compensated timebase rather than relying solely on an uncalibrated internal oscillator; multiplexing and sleep scheduling will also be designed around coin-cell limitations. I prefer fixing the actual root cause rather than applying temporary
€250 EUR in 14 days
4.4
4.4

As an experienced engineer and circuit designer, I understand the importance of developing efficient and user-friendly electronic systems. My skills in Circuit Design, Electronics, PCB Layout are perfectly aligned with your needs for a standalone LCD countdown timer. I have an extensive background in hardware designing using tools like KiCad and Eagle which will be beneficial for providing you with a detailed schematic and PCB layout. In addition to this, my proficiency in Arduino-compatible coding or bare-metal C will ensure the precise functionality of your timer, including accurate timing monitoring from the maximum of 1 hour down to the second level. Moreover, I am well-versed in addressing power efficiency concerns, which will help extend battery life while maintaining continuous operation over several months as you need. Lastly, my ability to clearly document complex engineering processes would deliver a comprehensive user manual that will enable easy reproduction or potential manufacturing of the design. Coupled with a demonstration video or high-quality photos, these deliverables will assure you of a reliable countdown timer that operates flawlessly throughout and concludes with exactly three clear beeps at timeout. Choose me for high-quality work that aligns perfectly with your project requirements.
€120 EUR in 3 days
4.8
4.8

Hi, I’ve carefully read and understood the requirements. I have experience with embedded hardware, low-power circuits, microcontrollers, and custom PCB design. I can design the complete standalone timer, including the MCU, 7-segment LCD, setting controls, precise countdown logic, and exactly three timed beeps. I’ll focus on low-power operation and suitable battery selection, while providing the schematic, PCB files, BOM, firmware, and assembly documentation. You can also check my portfolio for my previous embedded and PCB projects. Best regards, Ahmed
€140 EUR in 7 days
4.6
4.6

Hi there, I can create the compact standalone countdown timer you need, featuring a 7-segment LCD for readability and an audible alert. For the design, I'll ensure the microcontroller firmware operates efficiently with a straightforward interface using intuitive buttons or a rotary knob. The circuit will be optimized for power draw, allowing for months of usage with standard batteries. I will provide the schematic, PCB layout using KiCad, and a complete bill of materials. Additionally, I'll include firmware source code and a user manual for easy reproduction or handover to a manufacturer. Would you like specific recommendations on components that might simplify sourcing? Happy to discuss the details and suggest the best technical approach. Regards, Ali
€30 EUR in 1 day
3.7
3.7

Hi - Adelman here from Texas "LOW-POWER LCD COUNTDOWN TIMER" - you need a compact battery-powered device with accurate timing and exactly three clear beeps at timeout. I’d use a low-power microcontroller, sleep modes between updates, and a timing source chosen to meet your ±1 second accuracy target. The design will include the schematic, PCB, firmware, BOM, and assembly instructions. Is the coin-cell requirement fixed, or would you consider a larger battery if the beeper needs more power? Looking forward to work with you.
€200 EUR in 3 days
3.9
3.9

I am a perfect fit for your project. I can design a low-power, standalone 60-minute countdown timer with a readable 7-segment LCD, intuitive button controls, and an accurate three-beep alert system optimized for long coin cell battery life. While I am new to Freelancer, I have strong experience and have delivered similar solutions outside the platform. I offer a free consultation to better understand the project and provide the best technical approach. I would love to chat more about your project! Regards, Sonny Dube
€140 EUR in 7 days
3.3
3.3

Greetings Dear Hiring Manager I can design your low power countdown timer with precise firmware LCD control and triple beep alert 1. Is a custom LCD glass or segmented module preferred? 2. Must the coin cell power the beeper too? 3. Which setting method is preferred? 4. Is a piezo buzzer acceptable? 5. What are the target enclosure dimensions? Best Regards Dr Kainat
€31 EUR in 3 days
2.6
2.6

Hi, there. I have experience developing embedded devices involving microcontrollers, low-power hardware design, PCB integration, and C/C++ firmware for reliable standalone real-time applications. In a previous embedded project, I designed a battery-powered controller with a microcontroller, display interface, input handling, and timed output control. The main challenges were achieving accurate timing with low power consumption, ensuring stable hardware behavior, and creating simple user interaction without external systems; I solved them through RTC/timer-based firmware design, optimized sleep modes, debounced inputs, and efficient peripheral management. I am planning to develop your standalone countdown timer with a compact MCU-based design, 7-segment LCD driver, button/rotary input handling, and a low-power firmware architecture. I offer to provide the complete schematic, PCB layout, BOM, Arduino-compatible or bare-metal C firmware, assembly documentation, and prototype validation showing accurate countdown and the required three-beep timeout sequence. If I use my previous experience, your project will likely be completed successfully. Hope to discuss this in detail. Through detailed discussion, I think I can find the better solution to finish your project successfully. Thank you.
€200 EUR in 7 days
2.6
2.6

Hi, I can design a **compact, standalone countdown timer** with a 7-segment LCD, intuitive controls, accurate timing and an automatic three-beep alert. I have **16 years of embedded electronics, firmware and PCB R&D experience**, including low-power devices, microcontroller-based controllers, displays, timers and battery-powered products. My proposed solution includes: * Low-power MCU with accurate timekeeping and whole-second countdown. * 7-segment LCD with clear indoor readability. * Buttons or rotary encoder for setting, starting, pausing and resetting. * Exactly **three approximately one-second beeps** when the countdown reaches zero. * Optimized sleep modes and battery management. * Compact custom PCB designed in KiCad or Altium. **Important design consideration:** A coin cell may struggle to provide sufficient current for a loud buzzer and continuously readable display. I would evaluate the display, buzzer and battery together to maximize battery life without compromising usability. I can deliver the complete schematic, PCB files, BOM, firmware source, build instructions, user manual and assembly guide, along with prototype demonstration evidence. I will also validate timing against your **±1-second accuracy target over 60 minutes** Please message me for details of my previous **low-power embedded, display, timer and compact PCB projects**. Best regards, Subhash Suman Embedded Systems | Low-Power Design | PCB Design | Firmware | Battery-Powered Devices
€200 EUR in 7 days
2.3
2.3

Hello, I am an experienced Electronic Engineer specializing in Arduino, Prototyping, Firmware Development, Embedded Systems, PCB Layout, Microcontroller, Circuit Design, C Programming, PCB Design and Layout and Electronics. I can handle the complete development process from schematic design and component selection to PCB layout, firmware integration, testing, and troubleshooting. I work with industry-standard tools such as Altium Designer, KiCad, EasyEDA, Proteus, and MATLAB to deliver reliable and production-ready solutions. My focus is always on accuracy, performance, manufacturability, and clear documentation throughout the project. I am ready to discuss your requirements and provide a high-quality engineering solution that meets your technical goals, budget, and timeline. Thanks.
€30 EUR in 5 days
0.0
0.0

Hi, Your standalone LCD countdown timer with 3-beep alert is straightforward. I’d design a low-power ATmega328P-based circuit with a 7-segment driver (e.g., MAX7219) for brightness, use a piezo buzzer with 1s intervals for the triple-beep, and implement power-saving sleep modes to maximize coin cell life. I built a battery-powered kitchen timer with similar specs (7-seg display, 3-beep alarm) that ran 6 months on AA batteries. Happy to chat about component choices or PCB layout tools.
€30 EUR in 1 day
0.0
0.0

Hello! I am available to work on standalone LCD countdown timer hardware design and firmware development. I can start immediately by selecting an ultra-low-power microcontroller that handles segment driving while keeping battery draw low and I am well suited because I have built compact battery devices. One thing that I would love to know before I start is what exact coin cell battery size you prefer. I recently worked on a standalone digital timer with an LCD screen and buzzer output. I designed the schematic in KiCad using a low-power microcontroller with direct LCD driver support which ran on CR2032 batteries for over six months and achieved timing accuracy within half a second per hour using an external crystal oscillator. Best, Quantum Code Solution
€140 EUR in 7 days
0.0
0.0

Hi, the goal is a timer people can set quickly, read in daylight, and trust to give exactly three noticeable beeps without draining its coin cell. I would start with the schematic and power budget, then validate the display, buttons or encoder, buzzer, battery, and microcontroller on a small prototype before laying out the PCB. The firmware would provide clear set, start, reset, and timeout states, with Arduino-compatible C source and reproducible build instructions. The part that usually bites here is timing drift over a full hour. I would use a low-power timing reference and verify accuracy against a reference clock, rather than relying only on loop delays. A short press could adjust seconds while holding a control accelerates setting, making occasional use less frustrating. The deliverables would include KiCad or Eagle files, BOM, assembly notes, manual, source, and a demonstration recording. I would also document component substitutions where they affect battery life or sourcing. I have two questions: Q1: Which coin cell is preferred, CR2032 or another type, and what buzzer volume is acceptable indoors? Q2: Is one working prototype required, or should the design be prepared directly for small-batch manufacturing?
€200 EUR in 3 days
0.0
0.0

Hi We are available to take this on and get your standalone countdown timer working perfectly. The main issue with low-power 7-segment coin-cell designs is usually balancing the LCD drive/bias current with sleep-state power draw and driving the piezo directly. Are you planning to use an ultra-low-power MCU like an MSP430/STM32L or an ATtiny/Arduino-compatible base, and do you prefer a rotary encoder or dedicated pushbuttons for setting the minutes and seconds? We recently built a similar compact, battery-powered embedded hardware project that required custom micro-power timing and audible alert cycles. We designed the schematic and multi-layer PCB layout in KiCad, selected a high-contrast multiplexed 7-segment LCD, and optimized the C firmware to utilize deep sleep modes with hardware timer interrupts. We ensured the PCB trace routing optimized battery life and validated the exact timing logic and piezo driver to ensure clean, reliable tone bursts on timeout. We are eager to discuss the project further. Reach out to initiate a conversation! Best regards, Tech Ariba
€140 EUR in 7 days
0.0
0.0

With over a decade of experience in C programming, I am confident that I can deliver an excellent standalone LCD countdown timer solution for your project. My expertise includes embedded systems development and firmware programming, making this project well within my capabilities. Having worked on numerous projects that required precise timing, I understand the significance of accuracy in a countdown timer. I can assure you that your desired tolerance of ±1 s over the full hour will be met efficiently. Furthermore, as part of my service offering, I provide clear documentation and assemble detailed user manuals to ensure easy reproduction or handover to a manufacturer. In terms of power optimization, which is especially important for a coin cell-powered device meant for long-term use, I have a proven track record. My solutions not only meet functional requirements but also consider practical factors like battery life and simplification of sourcing components without compromising primary functionality. Since your project calls for sourcing substitution suggestions to potentially enhance battery life, I am well-suited to offer precisely tailored inputs towards reaching such an optimized design. Let's discuss further how we can bring your vision to life!
€250 EUR in 1 day
0.0
0.0

Hello, The part that usually fails here is the beep, not the timer. A CR2032 can’t supply a magnetic buzzer’s 20-30 mA pulse once it’s partly drained; the voltage sags, the MCU browns out mid-alarm and you get one or two beeps instead of three. I’d drive a piezo transducer at its resonant frequency (a few mA, still loud in a small room) with a reservoir capacitor, and use an MCU with a built-in LCD driver and a 32.768 kHz crystal. The internal oscillator alone drifts well past your ±1 s per hour. Firmware sleeps between 1-second RTC wakeups, which is what makes months on a coin cell realistic: c ISR(RTC_TICK) { // wakes the MCU once per second if (state == RUNNING && --remaining == 0) { state = ALARM; beeps = 3; } if (state == ALARM) { if (beeps--) piezo_start(2700, 300); // 2.7 kHz, 300 ms else state = IDLE; } lcd_show_mmss(remaining); } I’ve written C and C++ for 15 years, including low-level embedded work on CNC machining software. Is the coin cell a must, or would 2×AAA be acceptable? A coin cell works with the piezo design above; AAA gives a louder beep and years of standby. Kind regards, Karol
€50 EUR in 2 days
0.0
0.0

Hi there, The main challenge is delivering a self-contained, battery-powered countdown timer that remains readable, keeps timing within ±1 second over an hour, and produces exactly three evenly spaced beeps without unnecessary standby drain. I have strong hands-on experience with C Programming, Electronics, and Programming, and have solved similar problems involving embedded firmware timing, low-power hardware, and microcontroller-driven displays. My approach would be to: * Review the required operating behavior, battery constraints, display options, controls, and enclosure assumptions. * Identify the root design constraints and determine what can be reused versus what needs to be changed. * Implement a clean, maintainable solution using an Arduino-compatible or bare-metal C microcontroller, KiCad schematic/PCB design, and a complete BOM. * Test edge cases, reliability, timing accuracy, battery usage, display readability, button handling, and the exact three-beep sequence. * Deploy or integrate the fix without disrupting the existing system, including build instructions, assembly guidance, user documentation, and prototype demonstration evidence. For ±1-second accuracy across 60 minutes, I would use a calibrated crystal or suitably compensated timebase rather than relying solely on an uncalibrated internal oscillator; multiplexing and sleep scheduling will also be designed around coin-cell limitations. I prefer fixing the actual root cause rather than applying temporary
€250 EUR in 1 day
0.0
0.0

Torhout, Belgium
Member since Oct 9, 2026
$250-750 USD
$8-15 USD / hour
₹1500-12500 INR
$250-750 USD
$5000-10000 USD
€30-250 EUR
$30-250 USD
₹12500-37500 INR
$70-95 USD
£20-250 GBP
$1750-3500 USD
$30-250 USD
$15-25 AUD / hour
₹12500-37500 INR
$15-25 AUD / hour
$30-250 USD
₹1500-12500 INR
$250-750 AUD
₹12500-37500 INR
₹600-1500 INR