Fermé

Portable Power Station

We are looking for a freelancer or agency specialized in electronic engineering that can design a set of PCBs with the specifications mentioned in the freelancer document attached. The first PCB is an inverter and it is to be designed to be suitable for specifications of battery used in the system, should output a 220V 50Hz pure sine wave output that can support a load of up to 500W and safely tolerate surge power of up to 1000W. The first PCB board must also include a MPPT suitable for specifications of the solar panel array and battery used in the system. The second PCB to be designed is DC-DC converter that must include two USB output ports ( Normal and fast charging ) as well as a DC output port of 12V 10A and a car charger output of 12V 20A. An LCD must also be included and programmed to display the following information; Battery percentage,

Output power, Solar panel voltage and power. The third PCB is a rectifier designed according to standards set for charging a LiFePO4 battery used in the system, as efficiently and quickly as possible without disregarding battery safety and longevity. More details regarding specifications of deliverables will be found in the Freelancer Document attached.

Compétences : Electronique, Génie Électrique, Mise en Page PCB, Design de circuits, Microcontrôleur

en voir plus : generator power station works, freelancer power station siemens, electrical power station analysis software etap, cyprus electric power station, power station consultant japan, gas driven power station near chinchilla qld, 66kv power station engeneer skills, simulink model power station, short circuit calculation etap power station, industrial architecture power station archicad, design calculation grounding system power station, nanostation power station, power station trunk vlan, caterpillar 3600 power station, etap power station license, mettur thermal power station abb, commissioning thermal power station, diy portable power station, which of the following must be included in an export plan

Concernant l'employeur :
( 0 commentaires ) Dubai, United Arab Emirates

Nº du projet : #27952726

12 freelances font une offre moyenne de 682 $ pour ce travail

binyameen441

Hello, thank you for your job posting. I read your description about--PORTABLE POWER STATION I am a senior electrical engineer. I have plenty of experience in firmware development and micro-controller developments. I c Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 7 jours
(108 Commentaires)
6.4
avigupta0061

Best Electronic Engineering Expert at your doorstep! Dear Client, I can design a set of PCBs with the all mention specifications I have seen the pdf and could do it for you We couldn’t stop ourselves from bidding afte Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 2 jours
(13 Commentaires)
5.8
HarimohanG

Best Electronic Engineer Expert at your service! Dear Client, I can design a set of PCBs with the specifications mentioned After going through your project details, I am happy to inform you that these are an exact matc Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 2 jours
(2 Commentaires)
4.4
GERGX

Hello. I have 8+ years of experiences in PCB design and layout, firmware programming. - PCB layout and schematic capture with Altium, Cadence, Eagle, etc with multi-layer, flexible, high-speed embedded systems. - ARM: Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 7 jours
(2 Commentaires)
3.7
(5 Commentaires)
3.6
beemf1633

I have read your project description and PDF file. LCSC as well as JLCPCB both are good options. I made a lot of PCBs and will provide you gerber files at the end. On the other hand I will show you all simulations but Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 24 jours
(12 Commentaires)
3.6
aliabidlodhi74

Hello... I have read your requirement you want Portable Power Station. Lets discus details in chat. I have master degree in Mechatronics Electronics Engineering and I have 7 years of Industrial experience in dealing Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 15 jours
(8 Commentaires)
3.7
MedaniAhmed

Salam.. I have just seen your post, far as I understood you want.. 1- Inverter.. 2- DC - DC converter. 3- Rectifier. I only have some few questions, if the schematics already exist cause you asked for PCB design or Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 30 jours
(1 Évaluation)
2.1
superanas777

Hello. I have read your description carefully and I am very interested in your project. I am a professional electrical/electronics engineer and have actual experience in Embedded System Design based on PCB design and Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 20 jours
(1 Évaluation)
1.4
sivomakul

Hello, I have checked The requirement and understand that as well. I have created SIMILAR in past. Do you want to see the DEMO ??? Can will send you ?? Thanks.

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 7 jours
(0 Commentaires)
0.0
Frelanceryoung

Hello, Professionalism is the key to excellent quality in every project. I am online writer with years of experience and have knowledge on different topics. I have remarkable reviews from my clients who recommend my w Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 7 jours
(0 Commentaires)
0.0
LingarajMK

Hi, Thanks for sharing the requirement. We are expertise in product design, development and Testing (Hardware Design, Digital logic design (CPLD and FPGA), Schematics Entry, PCB Layout design, Software, Firmware, Mech Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 45 jours
(0 Commentaires)
0.0