
Closed
Posted
Paid on delivery
I am looking for an experienced Electronic Engineering Freelancer to design a custom, compact, all-in-one PCB for a premium adult collectible display base. The board will be manufactured using standard Turnkey PCBA (automated assembly), so the design must utilize readily available components from standard libraries (such as JLCPCB / LCSC component libraries). Core System Requirements: 1. Microcontroller Core: Integrated ATmega328P-AU (TQFP-32 surface mount package) with a 16MHz crystal oscillator and supporting circuitry. Programming/power interface must be a surface-mount USB Type-C port linked via a CH340G/C serial converter chip. 2. Power Architecture: Direct 5V DC power delivery completely driven over the Type-C USB interface (bypassing battery circuitry entirely). Must include a surface-mount PPTC resettable fuse (5V 2.0A or 2.5A) to safely handle concurrent current spikes. 3. Off-Board LED Interface: A 3-Pin JST-XH (2.54mm pitch) male header output socket labeled 5V, GND, and DATA. The DATA line trace must route directly to Digital Pin 6 of the microcontroller, featuring a surface-mount 330Ω to 470Ω inline protection resistor. 4. Infrared (IR) Remote Control Assembly: Footprint layout for an integrated TSOP38238 (or VS1838B) 38KHz IR receiver diode placed directly at the PCB's accessible outer edge. The Data Out line must route to Digital Pin 11 of the microcontroller core. 5. Dual-Channel Ultrasonic Mist Driver Circuit: Integrated 108KHz ultrasonic atomizer driver circuit layout to run two independent ceramic piezoelectric discs. • Bypass Requirement: The standard manual tactile push-button must be replaced/bypassed using an automated transistor circuit switch (e.g., NPN BC547, 2N2222, or a small logic-level MOSFET) connected straight to Digital Pin 2 of the microcontroller. • Output Interface: Two separate 2-Pin JST-XH (2.54mm pitch) header sockets at the board edge to plug in the atomizing discs. Design Shortcut Note: You do not need to design the ATmega328P/Arduino Nano core from scratch. You are highly encouraged to base the foundation layout on open-source, factory-verified reference hardware templates (such as OSHWLab/EasyEDA projects). Your primary custom design layout task involves cleanly integrating the 108KHz dual-mist circuit block and mapping out the transistor switch automation logic. Final Deliverables Required: A complete, verified Turnkey PCBA Production Package containing: • Extended Gerber Files (.zip format containing all board manufacturing layers and drill paths). • Bill of Materials (BOM spreadsheet with verified standard LCSC part numbers). • Component Placement List (CPL / Centroid coordinate file for automated pick-and-place robotics).
Project ID: 40753866
23 proposals
Remote project
Active 1 min ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
23 freelancers are bidding on average ₹8,420 INR for this job

Hi, I have experience in designing Circuits and can complete your project. I have expertise in the following: 1- Designing schematic and PCBA 2- Ordering the PCBA and getting boards manufactured. 3- Writing firmware for the PCBA to make sure everything works as expected. 4- I can also develop smartphone apps to communicate and control the hardware. If you wish we can discuss in chat. Thank you.
₹7,000 INR in 7 days
7.5
7.5

With a plethora of first-hand experience in all aspects of designing circuit boards, including using Eagle, Altium, KiCAD and EasyEDA, and even Fusion360 for CAD/housing design for PCBs, no stone will be left unturned when it comes to your custom PCB project. I have an ardent passion for this field and thus can guarantee the utmost precision and accuracy needed for your project. Likewise, working with Arduino and knowing how to maximize its potential will ensure the integrated ATmega328P-AU will function harmoniously within your device. Additionally, since you'd prefer not having to create a core from scratch, I am well-versed in using existing factory-verified reference hardware templates (ex. OSHWLab/EasyEDA). My vast experience in MATLAB/Simulink and Python programming also come into play as it helps me tackle complex algorithms involved in developing the most efficient board designs. Moreover, my advanced knowledge in signal processing techniques would prove beneficial for the IR remote control assembly portion of your project. I understand the importance of data flow precision and with that, I can guarantee efficient routing from the integrated TSOP38238 38KHz IR receiver diode to Digital Pin 11 of the microcontroller core. To conclude, I assure that my commitment to professionalism resonates with a fast turnaround time without compromising quality. Therefore partnering together means partnering with success!
₹7,000 INR in 7 days
7.0
7.0

Hey there! I’m Alok, A PCB, Circuit and Mechanical designer with a passion for turning ideas into rock-solid, high-performance circuit boards. even expert on Python, C, C++ With nearly a decade of experience, I’ve tackled everything from compact consumer gadgets to complex industrial systems—always with a focus on precision, efficiency, and reliability. # Schematic & Layout Design – Clean, optimized, and manufacturable. # Component Selection & Library Management – No surprises, just the right parts for the job. # Reverse Engineering – PCB cloning, replication, and improvements. # Gerber, BOM & CPL Generation – Ready for seamless production. # DFM & DFA Expertise – Because great design means smooth manufacturing. # Multi-Layer, Flex, & High-Density PCB Design – Whatever the project needs. If you need a PCB and Code that’s efficient, reliable, and built for real-world performance, let’s chat. I’d love to help bring your project to life!
₹7,900 INR in 5 days
5.9
5.9

Hello, I’m an Electronics & PCB Design Engineer experienced in compact embedded boards, ESP32/STM32/ATmega-based designs, power circuits, and JLCPCB/LCSC manufacturing. I can design this all-in-one PCB with: * ATmega328P-AU + 16MHz crystal + CH340G + USB-C * 5V power protection with PPTC fuse * JST-XH LED, IR receiver, and dual ultrasonic atomizer interfaces * Automated transistor/MOSFET switching from MCU GPIO * Clean PCB layout optimized for turnkey PCBA and readily available LCSC parts * Complete ERC/DRC and manufacturing verification I’ll also provide the complete production package: Extended Gerbers, verified LCSC BOM, and CPL/centroid file. I can also use a proven ATmega reference design as the foundation and focus the custom work on the dual 108kHz mist driver and integration. I’m ready to start.
₹7,000 INR in 7 days
5.6
5.6

As an AI-oriented firm, we may not seem like the obvious choice for a custom PCB design project. However, the complexity and level of precision required in this project align perfectly with our skill set. We have extensive experience in circuit design, electrical engineering, and embedded systems, which means we understand the intricacies involved in creating a compact, efficient and reliable PCB like your premium adult collectible display base needs. Moreover, our proficiency in using standard Turnkey PCBA manufacturing processes is a significant advantage when it comes to selecting readily available components from libraries like JLCPCB or LCSC. This helps us optimize manufacturing cost while ensuring top-notch performance from the chosen components. Our flair for squeezing out every ounce of efficiency will guarantee optimal use of the 5V power delivery system and reduced power loss in your custom solution.
₹7,000 INR in 7 days
5.1
5.1

Hi, Greetings! I am interested in working on your project. Could you please share the design details and technical requirements so we can discuss the project scope and key parameters in detail? I look forward to working with you. Thank you! Shivkant
₹12,000 INR in 7 days
4.7
4.7

I am an Embedded Systems and PCB Design Engineer with experience in Altium Designer, Kicad, Easyeda, Protious and custom hardware development. I can design your PCB from schematic to production-ready files, including: • Schematic Design • PCB Layout • Component Selection • Design Rule Check (DRC) • Gerber Generation • BOM Preparation • Manufacturing Support (JLCPCB, PCBWay, etc.) I have experience with ESP32, STM32, sensor interfaces, power supplies, RF modules, Ethernet, and industrial electronics. Please share the project requirements, schematic (if available), board dimensions, and any special requirements. I can start immediately. Looking forward to working with you.
₹12,000 INR in 5 days
5.0
5.0

Hi, I’ve carefully read and understood the requirements. I have hands-on experience in compact PCB design, ATmega/ESP32-based hardware, USB-C power, JST interfaces, sensor/driver circuits, and JLCPCB/LCSC turnkey manufacturing. I can integrate the ATmega328P-AU, CH340G, USB-C power with PPTC protection, LED and IR interfaces, and the dual-channel 108KHz mist driver with the required transistor control. I’ll provide a production-ready PCB with verified LCSC components, Gerbers, BOM, CPL, and manufacturing checks. I can also work from an existing reference design where appropriate to keep the development efficient. You can check my portfolio for my previous PCB and embedded hardware projects. Best regards, Ahmed
₹7,000 INR in 7 days
4.6
4.6

Hello, I am Santosh Chaulagain, a professional Electrical Engineer and PCB Designer with over 7 years of experience in schematic design, PCB layout, and embedded systems, including ESP32, IoT devices, analog and digital circuits. I have successfully completed multiple projects for clients worldwide, delivering reliable and manufacturable designs. I have carefully reviewed your project requirements and I am confident that I can provide a high-quality solution tailored to your needs. My expertise includes PCB design using industry standards, component selection, BOM preparation, Gerber generation, and design optimization for cost and performance. I always ensure that my designs are fabrication-ready and tested for reliability. I focus on clear communication, timely delivery, and customer satisfaction. I am happy to discuss your project in detail and provide revisions until the final result meets your expectations. Looking forward to working with you. Best regards, Santosh C. Electrical Engineer | PCB Designer | ESP32 & IoT Specialist
₹5,000 INR in 7 days
3.8
3.8

At HardFault, we are intrigued by your project involving the design of a custom PCB for a premium adult collectible display base, specifically the integration of an ATmega328P-AU microcontroller core with additional interfaces for a dual mist maker and IR remote control. With our expertise in embedded hardware design, particularly in creating custom PCBs and sensor front-ends, we are well-equipped to address the unique requirements of your project. Our team's experience with analog sensor interfacing and signal conditioning ensures the seamless operation of your ultrasonic atomizer circuit. Collaborating with us allows you to leverage a team’s combined strengths, ensuring broader skill coverage and redundancy, leading to a faster and more reliable output compared to a solo freelancer. We propose to start by aligning on the technical specifics, especially regarding the atomizer driver circuit layout. Could you share more about any design constraints we should consider in the final deliverables, especially concerning component sourcing?
₹8,960 INR in 12 days
3.4
3.4

I reviewed the complete architecture. The ATmega328P-AU/CH340G section can be based on proven reference hardware, but I would treat the 108 kHz dual mist-driver section as the critical part of the design rather than simply copying an Arduino board and adding connectors. Before PCB layout, I would verify the selected mist-driver topology against the actual piezo disc specifications, including operating voltage/current, 108 kHz drive conditions, switching-device ratings, and whether both channels must operate simultaneously. This is also important for confirming that the USB-C 5 V input and 2–2.5 A PPTC are correctly sized. I will integrate the ATmega328P-AU + 16 MHz clock, CH340G USB interface, USB-C power/input circuitry, D6 WS2812B output with series resistor, D11 IR receiver, and D2-controlled electronic mist switching. For PCB layout, the 108 kHz switching/current loops will be kept compact and separated from the MCU, USB and IR sections, with the external JST connectors positioned at accessible board edges. I can also select assembly-compatible parts with verified LCSC references and provide the complete Gerber, BOM and CPL package for JLCPCB turnkey assembly. I would first confirm the exact mist-disc specifications/reference driver before freezing that section of the schematic.
₹6,000 INR in 6 days
2.8
2.8

I regularly design compact, production-ready boards in EasyEDA and Altium Designer optimized specifically for automated JLCPCB/LCSC turnkey PCBA. For this build, I will implement an ATmega328P-AU (TQFP-32, 16MHz crystal) paired with a CH340 serial converter for direct programming over USB-C. The USB interface will feature 5.1k CC pull-down resistors, a 5V 2.0A/2.5A PPTC resettable fuse, and TVS diodes for robust power protection. Off-board interfaces include a 3-pin JST-XH header for LED control with an inline 330–470 ohm resistor on pin D6, and an edge-mounted 38kHz IR receiver with RC power filtering routed to pin D11. For the dual 108kHz mist generator, I will integrate a dual ceramic piezo resonant driver circuit switched through logic-level N-channel MOSFETs tied to pin D2 to fully automate the push-button trigger. High-frequency switching loops will be isolated on local ground pours with snubber protection to prevent noise coupling into the MCU, terminating in two edge-mounted 2-pin JST-XH sockets. Passives and common parts will be mapped to JLCPCB Basic and common Preferred LCSC parts to minimize loading fees. Deliverables include native EasyEDA Pro or Altium files, DRC-clean Gerbers, NC drill data, a JLCPCB BOM with exact LCSC part numbers, CPL centroid coordinates, and a 3D STEP model.
₹12,000 INR in 4 days
0.9
0.9

The critical part of this PCB is not the ATmega328P core—it is integrating the **dual 108 kHz mist-driver stage, USB-C power path, and MCU-controlled switching without noise, current-spike, or manufacturability problems.** That is where I would focus the design and validation effort. I can develop the compact all-in-one board around the **ATmega328P-AU + 16 MHz clock + CH340 USB interface**, with USB-C 5 V input, PPTC protection, LED output on D6 with series resistor, edge-mounted 38 kHz IR receiver on D11, and automated mist control from D2. For the atomizer section, I’ll treat the 108 kHz driver as a power/switching block rather than simply copying traces from an unknown reference. Component ratings, two-disc loading, current demand, grounding, decoupling, switching paths, thermal behavior and separation from the MCU/USB circuitry will be considered before layout. I can also select assembly-compatible components against **LCSC/JLCPCB availability**, assign correct SMT footprints, and perform schematic/ERC and PCB/DRC checks before generating the manufacturing package. Final handover will include **Gerbers, verified BOM with LCSC part numbers, CPL/pick-and-place data**, plus the editable design source so future revisions are possible.
₹7,000 INR in 7 days
0.0
0.0

Hi, Looking for an experienced technology partner to turn your concept into a reliable, production-ready product? We can help. Greetings from OSTronik India, we are specializing in Power Electronics, PCB Design, Embedded Systems, Firmware, IoT, AI Integration, and Mobile Application Development. Our Expertise ⚡ Power Electronics DC-DC & AC-DC converters, power supplies, power management, voltage/current regulation, protection, isolation, switching circuits and customized power solutions. ? PCB & Hardware Multilayer PCB design, schematic development, component selection, BOM preparation, Altium Designer, EMI/EMC considerations and production-ready files. ? Embedded & Firmware STM32, ESP32/ESP8266, PIC, AVR, Raspberry Pi, Embedded C/C++, sensor interfacing, hardware integration, debugging and optimization. ? IoT & Communication UART, SPI, I²C, CAN, RS-485, Modbus, MQTT, Wi-Fi, BLE, LAN, cloud connectivity and real-time monitoring. ? Mobile Applications Custom Android & iOS applications for device control, monitoring and data visualization. We can take your project from concept → design → prototype → testing → production, with a focus on reliability, performance and cost efficiency. Share your requirements or existing files, and let’s discuss how we can bring your product to life. Best Regards, Team OSTronik India Empowering Innovations
₹7,000 INR in 7 days
0.0
0.0

Throughout my career, I've consistently delivered complex board designs that optimize signal integrity, power distribution, and mechanical constraints – all of which align perfectly with your project's needs. Drawing from my deep experience in end-to-end PCB development, I am confident in delivering a premium all-in-one PCB that encompasses all your specified core system requirements, integrating your unique 108KHz dual-mist circuit and automated transistor switch as required. Importantly, I understand the value of readily available components from standard libraries in streamlining design flow and achieving effective automated assembly. This aligns strongly with your preference for JLCPCB/LCSC component libraries. Speaking of my design process, I work on the principle of selecting appropriate tools and references to embody efficiency without compromising quality – an ideology that has never failed me before. Finally, alongside my expertise in Circuit Design and PCB Layout, I bring to you a breadth of knowledge in battery hardware R&D, including waterproof configurations, balancing mechanisms, and thermal management. While this may not be core for your present project scope, it underlines my problem-solving approach and ability to tackle any challenges head-on. Together we can create not just a solid foundation for your Arduino-based project but also a functional art piece for years to come.
₹7,000 INR in 7 days
0.0
0.0

I’m a professional PCB Designer with 10 years of experience in PCB design and development. I have hands-on experience with Cadence Allegro, Altium Designer, KiCad, and PADS. My services include: • PCB Layout & Design • Schematic Design • Multilayer PCB Design • Component Placement & Routing • Gerber & Manufacturing Files • Design Review and Modifications • DFM/Manufacturing Support I focus on delivering accurate, reliable, and manufacturing-ready PCB designs according to the client’s requirements. I’m currently available for freelance and project-based PCB design work. I would be happy to discuss your project and provide the best possible solution.
₹11,000 INR in 7 days
0.0
0.0

I have carefully read your document and can independently complete SCH and PCB design  1. Add a current sampling circuit for the atomizer to prevent losses caused by dry burning of the atomizer. 2. Add some circuit components to prevent LED flicker during charging. 3. Add PMOS control to the overall current consumption in the 10K/10K voltage sampling circuit, otherwise there will be a current consumption of about 0.2mA at any time. 4. Complete two 108K dual channel ultrasonic atomization drive circuits as required 5. Install a 2.0A recoverable fuse on the Type-C interface and connect it to the ATmega328P-AU serial port via CH340. 6. Reserve an ISP burning port for ATmega328P-AU. 7. Provide complete manufacturing documents, including Gerber files, drilling files, Bill of Materials (BOM), and original design files.  I am in Shenzhen, the world's manufacturing capital, and can quickly implement solutions, including PCB manufacturing and soldering, and directly deliver PCBA.  Best regards
₹10,000 INR in 7 days
0.0
0.0

Hi, I'm Atharva. I specialize in electronic systems design and PCB layout, and I can deliver a highly optimized, turnkey-ready board for your collectible display base using KiCad. I completely understand the technical scope of this project. To ensure maximum reliability and a fast turnaround, I will leverage factory-verified open-source Arduino Nano and CH340G reference schematics for the ATmega328P-AU core and USB Type-C power delivery interface. For the custom integration, I will seamlessly design: Robust Power Architecture: Direct 5V delivery via USB-C, implementing the required PPTC resettable fuse to handle concurrent current spikes from the mist makers and LEDs. Exact Peripheral Routing: The WS2812B header mapped to Pin 6 (with a 470$\Omega$ inline protection resistor), and the edge-mounted 38KHz IR receiver footprint mapped to Pin 11. Mist Driver Automation: A custom transistor switching circuit (using a reliable logic-level MOSFET or NPN transistor) mapped to Pin 2 to successfully bypass the manual push-button on the dual-channel 108KHz ultrasonic atomizer. My final handoff will include the complete Turnkey PCBA Production Package perfectly formatted for JLCPCB: Extended Gerber files (.zip), an LCSC-indexed BOM spreadsheet, and the CPL/Centroid coordinate file for automated pick-and-place robotics. I am ready to start mapping the schematic immediately. Let's chat to finalize any specific mechanical constraints or dimensions for the final board edge.
₹6,000 INR in 10 days
0.0
0.0

Having honed my skills in circuit design and electronics for over five years, I am confident in my ability to deliver an exceptional product for your custom PCB design. I understand the unique requirements of your project, from integrating an Arduino core to incorporating the WS2812B interface and more. My hardware solutions expertise encompasses every stage of development - from comprehensive market research ensuring component availability, to schematic design and optimized PCB layout that takes into account thermal performance and manufacturability. Additionally, my familiarity with software solutions complements my hardware capabilities. I specialize in firmware development for microcontrollers like the ATmega328P, which is central to your project. With this experience, I guarantee seamless integration between the hardware and software aspects of your display base. In previous projects, I have consistently delivered results that prioritize precision, reliability, and long-term performance. My work on a commercial drone with a limited footprint and a kinetic lights control system requiring precise coding and control reflect the type of innovative solution-oriented approach I bring to all my projects. Choose me for a combination of expertise, reliability, efficient problem-solving and a commitment to creating designs with long term market applicability.
₹7,000 INR in 7 days
0.0
0.0

Kolkata, India
Member since Oct 6, 2026
£20000-50000 GBP
₹1500-12500 INR
$250-750 USD
₹1500-12500 INR
₹1500-12500 INR
$5000-10000 USD
$750-1500 USD
$250-750 USD
$10-30 USD
₹75000-150000 INR
₹1500-12500 INR
₹600-1500 INR
₹12500-37500 INR
₹750-1250 INR / hour
$250-750 USD
$15-25 USD / hour
$250-750 USD
₹37500-75000 INR
₹150000-250000 INR
£20-250 GBP