Terminé

Adrunio Timed EAZY-RL Relay Controller via DC Voltage Feedback Loop

This project is to control and run a pump to top my Lead Acid batteries up with distilled water for my solar system automatically on a 2 week to 1 month basis when the battery full charge voltage is met (31.4vdc).

I have a Adrunio, EAZY-RL Relay, and have a CJMCU-226 INA226 IIC Interface on order and a Standard Voltage Sensor Module (but only handles up to 25v). The work I need done is the coding to read the voltage feedback loop and initiate the send signal on the timed schedule.

This project is to control the EAZY-RL relay via send signal generated from the Adrunio (ex: [login to view URL]) on a timed interval (which is changeable) such as 1 month when a voltage threshold is met (ex: 31.4vdc but must be changeable).

Compétences : Arduino, Electronique

en voir plus : 200v dc motor controller project, avr brush dc motor controller, build phase dc speed controller, eazy-rl v2.3 manual, programmable timer relay 12v, delay timer switch, time relay switch, yyc-2 timer manual, timer relay 12v, timer switch module, drok timer relay, dc motor controller diy, dc motor controller make volt ac, dc motor digital controller, rs485 relay controller, arduino relay controller, dc voltage spike protection circuit, usb relay controller software, dc voltage regulator circuit, dc voltage limiter

Concernant l'employeur :
( 1 commentaire ) Utica, United States

Nº du projet : #19797260

Décerné à:

horaciodrut

Dear Sir, Mme, I am an electronic engineer with hands on experience in IoT product development, including but not restricted to: Arduino, sensors and actuators, Wifi and other wireless communication technologies, C/ Plus

%selectedBids___i_sum_sub_7% %project_currencyDetails_sign_sub_8% USD en 5 jours
(6 Commentaires)
4.8

7 freelance font une offre moyenne de $31 pour ce travail

xaainulabideen

For more details inbox me so that we can discuss in detail. For more details inbox me so that we can discuss in detail.

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 3 jours
(48 Commentaires)
5.8
pankajauengg

Hello! We will have to use RTC for timing and voltage sensor for the same. Kindly discuss about it over chat. For bid quote we will discuss later.

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 7 jours
(24 Commentaires)
4.8
Ko915

Hello, how are you. I am Youzong, high skilled microchip firmware developer. I read your requirements carefully and would like to apply to this job. I have good experiences of arduino controlling firmware. I hope t Plus

%bids___i_sum_sub_32% %project_currencyDetails_sign_sub_33% USD en 1 jour
(0 Commentaires)
0.0
LongNV7

Dear ! I think your project is very good. But we should not use modules for this project because if the actual production batch operation will not meet the requirements of the project. I think I have a solution for yo Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 7 jours
(2 Commentaires)
0.0
mesajju07

I've a good experience with Arduino and can code your project as your desired voltage I will do it by the signal conditioning method through which it detect upto how much do you want and what level is be set for this.

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 7 jours
(0 Commentaires)
0.0
edtadavid

Dear Sir, My proposal for this project is based on the Module LM2596 Step Down DC-DC that works as an operational amplifier subtracter. When the input voltage is 35v, the output voltage will be 5v, with this we will m Plus

%bids___i_sum_sub_35% %project_currencyDetails_sign_sub_36% USD en 2 jours
(0 Commentaires)
0.0