Fix My Radiomaster Boxer Error - screenshare needed

@jepita200

Hello, I have carefully reviewed your issue with the Radiomaster Boxer and EdgeTX configuration, especially regarding switch settings not saving, missing logical/global functions, and VTOL arming problems. I understand that your system was previously working and likely became unstable after the RTC battery replacement, which may have affected configuration integrity and SD card data. I can assist you with a structured troubleshooting approach: * Reviewing your current YAML/parameter files to identify conflicts or missing elements affecting arming * Guiding you step-by-step through restoring stable EdgeTX configuration and ensuring settings persist correctly * Assisting with radio calibration and RC mapping to meet safety requirements * Helping you implement a reliable two-stage arming logic (SA + SE with Thr < -98 condition) * Supporting testing and validation to ensure consistent arming behavior after reboot I am comfortable working via screen sharing (TeamViewer or similar) and can help you resolve this efficiently with clear guidance and practical fixes. My goal is to ensure your arming system works reliably every time and your VTOL is ready for safe operation. Best Regards, Mt Juetiara

@eliza019

Dear Client, I understand your Radiomaster Boxer (EdgeTX) setup is currently unstable after RTC battery replacement, causing SD/config corruption issues, missing Logical Functions/Global Settings, and failure in consistent arming behavior for your VTOL system. I have solid experience with EdgeTX/Radiomaster radios and drone flight controller integration (iNav / ArduPilot / Betaflight), including setup, recovery, and complex arming logic design. I can help you: • Diagnose and fix EdgeTX SD card/model config corruption • Restore missing Logical Functions and Global Settings pages • Review and correct YAML/parameter files for arming conflicts or missing fields • Build reliable two-stage arming logic using SA + SE with throttle safety gate (Thr < -98) • Verify RC mapping, calibration, and all pre-arm safety checks • Test and validate logic in SITL to ensure safe and repeatable arming after reboot I will take a structured approach: first stabilizing radio configuration, then validating signal/logic integrity, and finally ensuring consistent arming and flight readiness in STABILIZE and QLOITER modes. I’m available for screenshare/TeamViewer sessions and can work interactively until everything is fully resolved. Ready to start immediately and get your VTOL reliably airborne again.

@ammarahmed20

As a Full Stack Developer with 6+ years of experience, I am confident that I have the diverse skill set you need for this project. While my background is primarily in building web applications and SaaS platforms, I'm no stranger to complex problem areas - and your VTOL build certainly presents an intricate challenge! My ability to write clean, maintainable code and my commitment to reliability and scalability aligns perfectly with your need to "un-stick" your Radiomaster Boxer. What sets me apart is my adaptability and willingness to expand into new domains. While I haven't dabbled directly with VTOL builds before, troubleshooting with edgeTX programming and logical functions are well within my wheelhouse. Additionally, I assure you of a strong internet connection that will enable us to work seamlessly via screenshare or TeamViewer. I understand that the heart of the issue lies not just in fixing the error but also building a system that remains stable over time – something I've excelled at during my career. Therefore, not only will I guide you through the necessary steps for arming switch configuration- including constructing basic arming logic – but I guarantee success even after reboots. Let us merge our expertise so we can get your VTOL soaring again confidently. It's time to hit "Hire Me"!

@danh63

Hi, Your need for resolving the issues with your Radiomaster Boxer and ensuring reliable arming logic is clear. A key challenge here involves the corrupted settings due to the RTC battery replacement, which likely affected the YAML files and global settings. Addressing this will be critical for achieving consistent functionality and safe operation of your VTOL. I have extensive experience working with Radiomaster devices and EdgeTX programming, including troubleshooting YAML configurations and RC settings. In previous roles, I focused on resolving configuration conflicts and enhancing system reliability, ensuring that arming functions performed as expected even after reboots. This involved reviewing parameter files for discrepancies and implementing robust calibration procedures, which directly relates to your requirements. To tackle your project, I would follow these steps: - Assess the current YAML and parameter files to identify any inconsistencies. - Guide you through the necessary calibration and corrections to satisfy safety checks. - Test the revised parameters in SITL to validate that the aircraft arms correctly under various conditions. What specific issues have you noticed with the YAML files? - Are there any error messages that appear when you attempt to save settings? - Would you be available for a screenshare session to facilitate troubleshooting? Regards, Dan Hostetler

@stefanw71

Hello client, As I bid before, I am expert for this project. Looking forward to your feedback. Best, Stefan

@cadenv2

Hello Joshua Nice to see you again. I am always ready for your project. Let's start immediately. Looking forward to hearing from you soon. Best, Caden

@ammark477

Hi, I noticed you're facing issues with your Radiomaster Boxer, particularly with saving settings and missing critical global functions after replacing the RTC battery. It sounds like your main challenge is ensuring that the configurations are saved and that the arming switch functions correctly, as it's crucial for your VTOL build. I can help by diagnosing the file conflicts, correcting the YAML parameters, and guiding you through the necessary calibration and RC-map adjustments to ensure your arming switch operates reliably. My approach involves reviewing your existing config files thoroughly, identifying any discrepancies, and implementing robust arming logic with your specified conditions. With extensive experience in OpenTX and EdgeTX programming, along with a background in robotics and embedded systems, I've successfully resolved similar issues for clients before. For instance, I assisted another client in correcting their RC configurations and validating their flight parameters, ultimately leading to a successful test flight. As a quick tip, consider verifying that the RTC battery settings are correctly configured after replacement, as this often impacts system settings. Can we hop on a 10-minute call this week to discuss your project in detail? I can deliver an initial solution within 5 days.

@uzairelectronics

Hello, I’d be glad to help you get your Radiomaster Boxer and VTOL setup working properly again. It sounds like the RTC battery replacement may have corrupted some EdgeTX files or global settings, which is why functions, switch configs, and save behavior are broken. I have experience troubleshooting EdgeTX/OpenTX radios, restoring missing Logical/Global Functions, fixing SD card or config issues, and rebuilding reliable switch logic from scratch. I can review your current YAML/param files for conflicts, missing arming fields, RC mapping issues, or safety check problems that may be blocking arming. I’ll also help rebuild your two-stage arming setup with SA + SE and Thr < -98 exactly as needed. If required, I can guide radio recalibration, channel corrections, and test parameters through SITL before real flight. My focus is making sure your arming works consistently after every reboot and that STABILIZE/QLOITER modes arm cleanly and safely. I’m comfortable working through screenshare/TeamViewer and can help step by step until everything is reliable again. Best regards, Engr. Muhammad Uzair

@imranfaiz948

Hi, I can help you fix your Radiomaster Boxer and get your VTOL arming working properly ? I’ve worked with EdgeTX radios and understand issues like SD card corruption, missing global settings, and config not saving after RTC battery changes. I’ll help you restore the radio setup, fix logical functions, and make sure configs save correctly. I can also review your YAML/param files to find anything blocking arming and guide you through proper calibration and RC mapping. For arming logic, I’ll set up a clean two-stage switch (SA + SE with Thr < -98) and make sure it works reliably even after reboot. If needed, we can test everything in SITL to confirm stable behavior before flight. I’m comfortable working via screen share and can troubleshoot step by step with you. Let’s get your system armed and flying again. Best regards, Engr. Muhammad Imran