Fermé

Red/Green light with Arduino and remote control

We're looking to reuse some parts from a traffic light that had a simple remote control to automate it's functionality.

We have:

- 24V Red LED board

- 24V Green LED board

- Two sets of electric eyes (24V) - when the beam is interrupted, one of the wires is powered for as long as the beam is interrupted.

- Two remote controls (optional)

The traffic light will be used on a track and needs to have the following functionality, :

When Eye 1 (start) is triggered, send a wireless signal to the traffic light to turn red.

When Eye 2 (end) is triggered, send a wireless signal to the traffic light to turn green.

Another way to operate can be using a two-button remote control that overrides the Eyes. One button will serve as an on/off switch for the red light, the other button as an on/off switch for the green light. Both lights cannot be on at the same time. If both lights are off from the remote, the Electric Eyes take over again.

Another exception is if Eye 1 is triggered multiple times before Eye 2 is triggered.

The light should stay red until Eye 2 is triggered as many times in a row as Eye 1. In other words, if two cars pass the start line, the light should stay red until both cars pass the finish.

EDIT:
Parts we need to reuse:
-24V Red and Green LED board
-Two sets of electric eyes

Parts needed to be suggested:
-RF system

I believe the easiest way would be to buy an RF kit with 3 remotes and a receiver. We would use 1 for the manual function, and the other two for each Electric Eye. The receiver would of course be in the traffic light.

The system will most likely be powered by a car battery with a solar panel to keep most of the charge, but will also be regularly recharged. If we find a 24V battery that will be great, otherwise we'll use a 12V with a converter

Parts needed to be suggested:
-RF system
-Hardware to power the Arduino and wireless transmitters and receiver coming for a 24V source.

Compétences : Arduino, Programmation C, Programmation C++, Raspberry Pi

Voir plus : remote control arduino freelance, arduino light control wireless, wireless switch light control arduino, arduino light control, arduino light control internet, arduino light switch control, wireless light control arduino, arduino light wireless control, arduino control wireless light, develop remote control agent, freelancer remote control, remote control wm6, schematic diagram remote control helicopter, webcam remote control java, remote control using gsm project

Concernant l'employeur :
( 0 commentaires ) Montreal, Canada

N° du projet : #12646976

23 freelance ont fait une offre moyenne de 249 $ pour ce travail

sagradoamicus

A proposal has not yet been provided

500 $ CAD en 10 jours
(77 Commentaires)
6.8
mechatronicsengr

Hi, I hope you are doing well. I have experience with Light control using Arduino and Remote Control. I have reviewed your project details and I would like to discuss it in more details. Looking Forward, Khaw Plus

473 $ CAD en 3 jours
(36 Commentaires)
5.9
geekyexperts

Hello, I am an Electronics and Embedded system developer. I have experience in Digital and Analog electronic design and Matlab. i can help you with this project work. Kindly check my profile. Reply me back and will dis Plus

500 $ CAD en 3 jours
(21 Commentaires)
5.8
RobinLabPtyLtd

Hi, Let's have a quick chat about your project details. MCU (Arduino or alike) and RF transmiters can be powered from 24/12V source with a simple DC-DC converter. RF transmitter/receiver is not an issue either. Plus

300 $ CAD en 5 jours
(17 Commentaires)
5.1
ranganathp

FREELANCER RECOMMENDED ------------------------------------------------------ Can help... I am an Expert... Lets Start! Please start a Discussion with me and we can get started from there... Please check the past p Plus

600 $ CAD en 7 jours
(14 Commentaires)
4.9
uetian09ee506

I am an Electrical Engineer having specialization in Electronics and Control, teaching in Electrical Department at FAST National University Pakistan. I am also persuing my MS degree in Electrical Engineering with speci Plus

250 $ CAD en 3 jours
(9 Commentaires)
4.4
amelectronics

Hello dear I have experience in designing electronics circuits and can make your project. I will make your project practically on breadboard and will provide you circuit, code and PCB design. I can also develop androi Plus

300 $ CAD en 5 jours
(6 Commentaires)
4.1
poduzov

Hi I'm an electronics engineer with 10+ years of experience and can do this job. All this can be done without any controller - just relays. As a remote I would suggest something like this Owfeel RF 24V One Tr Plus

83 $ CAD en 3 jours
(1 Commentaire)
3.6
ahmad5857

Hi sir, We have read your project and we can do it for you on low rates. We assure you the quality of service through various checks that are employed to avoid any compromise on quality of work. Let me introdu Plus

200 $ CAD en 10 jours
(4 Commentaires)
3.4
SqUa11

A proposal has not yet been provided

155 $ CAD en 12 jours
(3 Commentaires)
3.0
saytinh

A proposal has not yet been provided

40 $ CAD en 15 jours
(4 Commentaires)
2.0
mvish88

Dear Employer, Hire me, I Can do this project. I have all the modules for RF remote. I am experienced electronics enthusiast working in the field since 8 years. My work area includes Embedded Systems (Hardware & S Plus

194 $ CAD en 15 jours
(1 Commentaire)
2.1
goldsea808

[url removed, login to view] [url removed, login to view] [url removed, login to view] ================================================================ Hello,how ar Plus

300 $ CAD en 3 jours
(1 Commentaire)
0.3
ahsandilawarr11

i am assistant technical manager of sublime enterprise. i have 5 year experiense of hardware & software designing. i can complete your project as you want

166 $ CAD en 5 jours
(1 Commentaire)
0.0
beyobox

A proposal has not yet been provided

222 $ CAD en 10 jours
(0 Commentaires)
0.0
votuananhs

Hello, in my understanding, you really have some parts in this project such as main kit and source for this. Now you want to add some new features on this and support new rf kit. Right ? If possible, I would like to ha Plus

200 $ CAD en 15 jours
(0 Commentaires)
0.0
alateinfotech

Hi there, we are new to freelancer, We are expert in both hardware and software development in field of electronics, having 2+ years of experience in circuit designing/debugging, coding, MatLab and various micro-contr Plus

250 $ CAD en 8 jours
(0 Commentaires)
0.0
SantoshKGD

Hi, We can design using Microchip/ST micrcontollers and with RF modules. Please share your requirements for the same. Thanks and Regards, Santosh

333 $ CAD en 10 jours
(0 Commentaires)
0.0
Saptarshi1104

Hi, I am an engineering student, studying in 3rd year, electronics department. I do my own project with ARDUINO. I can help you with your project. Here you have not mentioned the way of making it wireless( like Bluetoo Plus

166 $ CAD en 10 jours
(1 Commentaire)
0.0
aminjamhari

Hi There/Greetings/ I'm expert in embedded system development. I hope you could share more details about the project/job such as: 1. Does the freelancer need to develop the hardware or software part only? 2. The Plus

250 $ CAD en 7 jours
(0 Commentaires)
0.0