Fermé

Motor Controlled by Proximity Switch, Design & Program.

I have a simple project that I need help with. I have attached a photo showing the layout. I have a battery attached to a gear motor that moves a magnet up and down slide that is attached to a pole. The motor is setup in such a way that the motor only has to run in one direction to accomplish this up and down motion. I want to setup a magnetic proxitmity switch at the top of the pole that will tell the motor to start and stop when it either senses or does not sense the magnet. My thought is that the best way to accomplish this is with a simple microprocessor with simple code that controls the power coming from the battery. It will run a pattern, Here is a breakdown of what I want to happen in the pattern:

1. Magnet in position 1 with proximity 1 recognizing it - Motor stopped.

2. Magnet in position 1 with proximity 1 NOT recognizing it - Motor Running.

3. Magnet in position 1 with proximity 1 recognizing it - Motor stopped.

I will need to be able to adjust the sensitivity of the proximity sensor so that I can get the magnet to stop in the right place. I need the project completed ASAP.

I think it's pretty easy just the correct way to wire it, the programming, and what chip to use are beyond me. I am hoping to find someone who can work on this easy part because our next step is to include a timer and a remote to the next model and would like to use the same person for the next job.

Compétences : Programmation C, Génie Électrique, Electronique, Visual Basic

Voir plus : motor controlled proximity sensor, programming proximity sensor motor, work gear, top programming, best way start programming, person one photo, remote programming job, pretty design, power program, next gear, need help programming project, my wire, motor design program, motion job, motion design job, want start programming, job programming find, step design, help find right job, find remote programming job, find job design, design magnetic, design controls, programming power, beyond design

Concernant l'employeur :
( 1 commentaire ) Wesley Chapel, United States

N° du projet : #1007197

18 freelance ont fait une offre moyenne de 306 $ pour ce travail

TopGunPk

Hello. Please see PM.

180 $ USD en 2 jours
(7 Commentaires)
4.5
zszabo

Hi, Please see PM, BR Zoltan

500 $ USD en 20 jours
(3 Commentaires)
3.9
GreenlightAV

Please see my message to you.

240 $ USD en 15 jours
(2 Commentaires)
3.9
hcooper84037

Take a look at the offering I have at www.pic-bee.com, this should provide you with a solution for both the first and second stage. It will require a small amount of custom firmware but the hall sensor to detect the m Plus

200 $ USD en 20 jours
(1 Commentaire)
3.8
alit56

20+ yeas experience in embedded design, especially with PIC uCs.

200 $ USD en 14 jours
(5 Commentaires)
3.6
sbk

please check your pmb

220 $ USD en 4 jours
(3 Commentaires)
3.4
JJdatajobs

Hello 'seventhroom', Please see my PM. Thank you. With regards, JJdatajobs.

50 $ USD en 1 jour
(5 Commentaires)
3.1
adipdutt

Please see PMB

220 $ USD en 7 jours
(3 Commentaires)
3.0
amitj9

Hi, This can be done using a low-cost microcontroller from Micrcohip. I have been working with Microconroller programming and hardware designing since 20 years. This is quite simple to implement. Amit desi Plus

250 $ USD en 20 jours
(1 Commentaire)
2.4
IoliteTech

Hi, Please Check PM.

45 $ USD en 2 jours
(2 Commentaires)
1.7
AbhaBrajesh1956

I can do your project, Abha

220 $ USD en 30 jours
(1 Commentaire)
1.0
progsel

HI, in the past I already developed littlemunt like this, for sure NOT PROBLEM AT ALL. But I have a question, when the motor is position 1 (motor off) whos start the process? thank you

500 $ USD en 20 jours
(0 Commentaires)
0.0
smartknight92200

'm interested in your project i'll use PIC16f84 micro-controller and IRF740 for motor power control.I'll receive half paid at delivery and the second half will be after testing the circuit and its functionality.

80 $ USD en 4 jours
(0 Commentaires)
0.0
racorage

I have worked with microcontroller based application for 5 years now. I have experience of working with proximity sensors using magnets.

200 $ USD en 10 jours
(0 Commentaires)
0.0
hidalgoem

Hello, I have experience in motor control, see my PM.

180 $ USD en 8 jours
(0 Commentaires)
0.0
dharminec

you will get your project in time.

2000 $ USD en 20 jours
(0 Commentaires)
0.0
sanwal399

hi i am working on the embeded systems for last 10 years . ur project canbe controllerd by microcontroller made by microchip .

175 $ USD en 4 jours
(0 Commentaires)
0.0
YuriMat

Please see pm.

40 $ USD en 2 jours
(0 Commentaires)
0.0