
Completed
Posted
Paid on delivery
I need a script to automate a Shelly 4PM device to water 4 zones using normally open valves. before it starts run the pump on another shelly device, turn off the pump when finished. The zones should activate one after another for 15 minutes each, every day. Plus i cant allow the pump to run at any time with all 4 valves on(closed) so i need the script to off (open) the next zone for 10 seconds before off (closing) the next zone. if possible push notifications for starting ea zone, and push notification when all complete an pump off Requirements: - Zone activation: All 4 zones automatically, one after another for 15 minutes each - Schedule: Every day - Start time: A specific time I will provide Ideal Skills and Experience: - Experience with Shelly devices - Proficiency in scripting and automation - Familiarity with irrigation systems and valve control
Project ID: 40786663
85 proposals
Remote project
Active 6 days ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs

Hi, Adelman here from Texas. SHELLY IRRIGATION SEQUENCING: the key is preventing the pump from running while all four normally open valves are closed. I’d use a scheduled Shelly script to start the pump, open each zone with a 10-second overlap before switching zones, run each for 15 minutes, and shut down the pump after the final zone. I’d also add zone-start and completion notifications if supported. What Shelly models and firmware versions are you using for the controller and pump? Looking forward to work with you.
$200 AUD in 4 days
3.0
3.0
85 freelancers are bidding on average $135 AUD for this job

The important part here is not just making 4 zones run for 15 minutes each; it’s making sure the pump never runs against closed valves during changeover. I’d handle this with a proper zone-to-zone handoff script on Shelly so the next valve opens first, waits 10 seconds, and only then closes the previous one, while also starting the pump before the cycle and shutting it down at the end. I’ve worked on device automation and control logic where sequencing matters more than the UI, and that’s exactly the case here. With Shelly jobs, the difference between a basic timer and a reliable script is in the safeguards, edge cases, and clean scheduling. If you want, I can also structure the script so the run times and start time are easy to edit later. - Is the pump relay on a separate Shelly with a fixed IP/name already set? - Do you want the notifications through Shelly app only, or via another service if needed?
$240 AUD in 4 days
7.4
7.4

Hi, I can develop a reliable Shelly script to automate all 4 irrigation zones daily, control the pump, and send push notifications. The main challenge is safely switching between normally open valves by opening the next zone 10 seconds before closing the previous one, preventing all valves from being closed while the pump is running.
$150 AUD in 1 day
7.3
7.3

Hello, I'm Denis, a full-stack developer, and I have built automation scripts for smart home devices that control physical systems like pumps and valves through timed sequences. You need to automate watering across 4 zones on a schedule, with each zone running for 15 minutes one after another. The real constraint is that the pump cannot run while all valves are closed, so you need a 10-second overlap where the next zone opens before the current one closes. You also want notifications when each zone starts and when the job finishes. I would write a script that runs on a schedule using the Shelly API to control both devices. The script would start the pump, then loop through each zone: open the next valve, wait 10 seconds, close the previous valve, wait 15 minutes, then repeat. After the last zone closes, it shuts down the pump and sends notifications at each step. I would test it against your actual devices before going live. The critical part is the valve overlap logic. I would build it so the script always checks that at least one valve is open before the pump runs, preventing damage. The main risk is timing precision if the Shelly API has latency, so I would add small buffers and error handling to catch missed commands and retry them. I can start working right away. Let's connect and discuss the details. Thanks, Denis.
$30 AUD in 3 days
6.4
6.4

Hello, I went through your watering setup and the part that really matters is the pump safety, not just a simple timer. Normally open valves means power on equals shut, so the pump must never run while all 4 is closed. That can cook the pump pretty quick. The script should treat that like a hard stop. Here is the daily run in plain words. At the time you give me, zone 1 opens first and the other three stays shut, then the pump on the second Shelly kicks in. Each zone gets about 15 minutes, one after the other. When its time to swap, the next zone opens and we wait about 10 seconds so water still has a way out, then the finished zone closes. After zone 4, the pump switches off before that last valve shuts. If a Shelly dont answer mid run, the pump gets killed straight away and you get a warning instead of the script carrying on blind. You will get a push when each zone starts, and another when the whole lot is done and the pump is off. The start time sits in one spot, so changing it later is easy and you dont have to touch the safety bits. I would dry test the changeover with the pump command blocked, then do one real cycle with you watching so we know the overlap feels right. I can have this sorted in about a week once I have both Shelly details and the time you want it to...
$160 AUD in 7 days
6.1
6.1

Your key constraint is the pump protection during zone switching, because with normally open valves the script needs to avoid any moment where flow is blocked. I’d set this up so the pump starts first, each zone runs in sequence for 15 minutes, and the next zone is opened for 10 seconds before the previous one is closed, then the pump turns off after the last cycle. This is the kind of automation task where careful logic matters more than a long feature list. I’ve handled scripting and workflow setups that depend on exact timing, relay order, and safe failover behavior, which fits this irrigation use case well. I can also keep the schedule values cleanly editable so changing the daily start time later is simple. - Is the Shelly 4PM already controlling all 4 valve outputs right now? - Should the system skip the run if the pump Shelly is offline, or just try again? - Have you already enabled the notification method you prefer?
$230 AUD in 5 days
6.1
6.1

The pump interlock is what matters here. If a valve sticks or the script crashes mid-cycle, you need failsafe logic that won't let the pump run into a closed system. I'd build this in JavaScript on the Shelly scripting engine itself so it runs locally without needing a separate server. Each zone transition would enforce a 10-second overlap where the next valve opens before the current one closes, and I'd add a watchdog timer that kills the pump if all four relays ever read closed at once. I've done similar work automating hardware sequences where order and timing prevent physical damage, most recently an MT5 trading bot with layered risk cutoffs. You can see that and other automation work at ffulb.com. I'd wire up push notifications through Shelly's webhook API to hit your phone at each stage.
$112 AUD in 5 days
5.9
5.9

Hi — Singh here. I'll write a Shelly script to automate your 4-zone irrigation: run the pump on a second Shelly, activate zones one by one for 15 minutes each daily at your chosen start time, with a 10-second overlap (next zone opens before current closes) so the pump never runs with all valves closed, plus push notifications for each zone start and completion when the pump shuts off. I'm fully confident I can deliver this for you, and I will give my 100% until it works exactly the way you want. Ready to begin as soon as you are. Thanks
$200 AUD in 5 days
6.4
6.4

Hi there, I see you're looking for a script to automate your Shelly 4PM watering system for four different zones, making sure the pump runs correctly and that no valves are open simultaneously. I can help you create a solution that activates each zone for 15 minutes in sequence, with a 10-second interval to prevent any overlap. I will also integrate push notifications to keep you updated on the watering process. With 4+ years of experience in scripting and automation, particularly with Shelly devices, I understand how to efficiently manage irrigation systems. I will ensure the script meets your specific daily schedule requirements and provides clear notifications once the watering is complete. Could you let me know what specific start time you have in mind for the watering schedule? Best regards, Arslan Shahid
$30 AUD in 3 days
5.7
5.7

Hi, I’ve built automation workflows that coordinate device actions through reliable scripting and API integration. You need a daily schedule that runs a Shelly 4PM to open normally open valves across 4 zones, one after another for 15 minutes, while pre-starting and safely stopping a pump Shelly device. I’ve delivered dependable automation scripts with timed state transitions and alerts. Best, Razmik
$100 AUD in 2 days
5.0
5.0

Hello, I can help you automate your four-zone watering system using Shelly devices, with reliable scheduling and safe pump control. I would develop a script that starts the pump at your chosen time each day, activates each zone sequentially for 15 minutes, and switches the pump off after the final zone finishes. To protect the pump, I’ll implement the 10-second overlap between valve transitions, opening the next zone before closing the current one to avoid a condition where all valves are closed. I’ll also add clear execution logic, error handling, and push notifications when each zone starts and when the complete watering cycle finishes with the pump switched off. I’ll verify the device IDs, relay behavior, and timing settings against your Shelly models before finalizing the script. My priority is safe, dependable automation that runs without daily manual intervention. Looking forward to working with you. Thanks.
$170 AUD in 3 days
5.2
5.2

Hi, Fernando here, from Mexico. Building your automated script for watering system with 4 zones is doable; what matters most is a device that behaves the same in the field as on the bench. I'm a senior embedded and electronics engineer with 12+ years of experience working with Embedded Systems and C Programming. For your automated script, the real challenge is timing, power and real conditions. A common issue: testing only on the bench, so problems appear once the device runs in real conditions. My plan: first, review the schematic, pin map and timing requirements. Then, write the firmware in small modules, each tested on the board. Finally, test on the real hardware under load, power loss and bad signal. I'd start with the core firmware features as phase one. I've done firmware work before. A few questions to better understand the scope: 1. Should firmware update over the air? That needs a safe bootloader and a fallback image, planned from the start. 2. Log raw readings during testing? I'd recommend it, you compare against a reference instead of guessing. 3. Who uses the device, engineers or everyday users? Everyday users need clear status lights and safe defaults. I can start right away. Happy to go over the details here in chat and suggest the best approach. Looking forward to hearing from you, Fernando
$100 AUD in 1 day
4.8
4.8

Hi there, I am excited to submit my proposal for your project on developing an automated script for your Shelly 4PM watering system. With a strong background in scripting, automation, and home automation systems, I am confident in delivering a solution that meets your needs. Understanding your requirements, I propose creating a robust script using Python or Node.js, integrating seamlessly with your Shelly devices. This script will automate the watering of four zones, activating each zone sequentially for 15 minutes daily, as per your specified start time. To ensure efficient pump operation, the script will manage the valves to prevent simultaneous closure, avoiding potential system overloads. The script will open the next zone for 10 seconds before closing the previous one, ensuring smooth transitions. Additionally, I will integrate push notifications to alert you at the start of each zone and upon completion of the watering cycle, providing real-time updates on system status. My experience with Shelly devices and embedded systems will facilitate a seamless automation process, enhancing the functionality of your irrigation setup. I am eager to bring my expertise to your project and ensure a reliable and efficient automated watering system. Looking forward to the opportunity to work together. Best Regards,
$30 AUD in 5 days
5.4
5.4

What makes this job tricky is the transition between zones, not the daily timer itself. The script needs to manage the pump and valves in the right order every time, including the 10-second overlap between zones, so the pump never ends up running with all valve paths shut. I’ve worked on automation setups where sequencing and reliability are the whole job, and Shelly-style scripting is well suited for this kind of control flow. The goal would be a simple, dependable routine you can leave running daily without having to babysit it. Push alerts for each zone start and final completion can be added if your setup supports them. - Which Shelly model is controlling the pump? - Do you want all 4 zones fixed at 15 minutes, or should each zone be easy to adjust separately later?
$218 AUD in 6 days
5.2
5.2

Hello, "SHELLY VALVE SEQUENCE SCRIPT" - Automate your Shelly 4PM so each of the 4 zones runs 15 minutes in sequence, with the pump Shelly turned on before each cycle and off once finished. Manual control of valves and pump risks the pump running against closed zones, which can damage it over time. I'd write a Shelly script (device-side, no server needed) that starts the pump, opens zone 1, after 15 minutes opens zone 2 for 10 seconds before closing zone 1, and repeats this overlap pattern through all 4 zones so the pump never runs fully closed. After zone 4 finishes, it closes the valve and shuts the pump off. Daily scheduling would run natively on the Shelly at your chosen start time, with push notifications via the Shelly app webhook/action feature for each zone start and for pump-off/completion. I have experience with embedded automation and scripting logic like this, and can hand over the tested script with clear setup notes. Looking forward to work with you. Thanks
$200 AUD in 2 days
4.9
4.9

Done this before with Shelly relays, normally open valves need the logic inverted so a dropped connection cannot leave a zone stuck open. I would script the 4PM over its local HTTP API or MQTT, set zone durations and sequencing, and add a dead man's cutoff for safety. Can start today, working script by Thursday. These numbers are rough from the post, happy to firm them up once I see your zone layout and schedule needs. Want me to send a quick plan?
$150 AUD in 4 days
4.7
4.7

Hello, I checked your project "Automated Script for Watering System" and already have a clear understanding of your requirements and how to deliver them efficiently. I have solid experience in JavaScript, Python, Node.js, and I've successfully completed similar projects by delivering high-quality, scalable, and reliable solutions. Why choose me? * Strong expertise in JavaScript, Python, Node.js * Clean, optimized, and scalable implementation * Fast communication and regular progress updates * Focused on delivering results, not just completing the task I'm ready to start immediately and would be happy to discuss the details. Best regards, Umer
$40 AUD in 1 day
4.3
4.3

Hi, SARA here, from Serbia. Optimizing your existing Amazon listings is doable; what matters most is content that sounds like you and gets read to the end. I'm a content writing specialist. I work with projects like this. With Amazon, the real challenge is matching your voice and audience. A common issue: writing to a word count instead of to the reader, so pieces feel padded. My plan: first, agree the audience, tone and outline for each piece. Then, write the first piece and adjust it to your feedback. Finally, finish the rest in that voice and proofread each one. I've done writing work before, so I check early for tone drifting between pieces. A few questions to better understand the scope: 1. Does anyone else need to approve the text? Then I share an outline first, so late feedback does not reshape it. 2. Use short paragraphs with subheadings? I'd recommend it, most readers scan on phones before they read. 3. Is the text for US or UK readers? I match spelling, terms and phrasing to those readers. I can start right away. Happy to go over the details here in chat and suggest the best approach. Looking forward to hearing from you, SARA.
$180 AUD in 2 days
4.0
4.0

The real constraint is the pump: a closed-valve deadhead can cook it, so the sequence must guarantee at least one valve open whenever the pump runs. A naive loop gets that wrong. I'd write it as a state machine on the 4PM's own scripting engine — open zone 1, start the pump on the other Shelly, 15 min, open the next valve, hold 10 s with both open, close the previous, repeat, pump off last and only after every valve reports closed. Watchdog on each call: if the pump doesn't report on, abort and notify instead of watering dry. Daily start via the device's own schedule, not external cron, so a router outage doesn't kill the run. Notifications through a webhook or Telegram call, one per zone start and one at completion. I've built Node/JS automation driving physical devices over HTTP and MQTT. Which Shelly model runs the pump, and do you have MQTT or only the cloud app?
$160 AUD in 4 days
3.2
3.2

Hello, I'm based in Japan, blending strong technical skills and rich experiences with Japanese discipline, punctuality, and attention to detail. I'll work efficiently to complete your project perfectly, and as quickly as possible. Unfortunately, I can't write full description in this by character limit of this site and so I hope we can discuss more detail in direct chat. Looking forward your response, Warmly Regards.
$230 AUD in 7 days
3.3
3.3

Hi, your irrigation should run every day without the pump ever facing four closed valves or requiring manual supervision. I’d first map the Shelly 4PM outputs, valve wiring, pump relay, and daily start time, then build and test the JavaScript automation directly around that sequence. The handoff is the part that usually bites here: the next normally open valve must open for 10 seconds before the current zone closes, so the pump always has a safe water path. The script would start the pump, run each zone for 15 minutes, send a zone notification, and shut the pump down only after the final zone finishes. I’d also guard against a restart or interrupted run leaving the pump active, and keep the timing easy to adjust later. This fits my background in JavaScript, Python, embedded automation, and API integration. I have two questions: Q1: Should the schedule use the Shelly’s local time, and what start time and timezone should be configured? Q2: Are the valves confirmed normally open, with the relay state mapped so “on” opens each zone?
$50 AUD in 1 day
3.0
3.0

Gidgegannup, Australia
Payment method verified
Member since Oct 26, 2026
₹1500-12500 INR
€250-750 EUR
$15-25 USD / hour
₹1500-12500 INR
$250-750 USD
£18-36 GBP / hour
₹1500-12500 INR
$30-250 USD
$250-750 USD
min $100000 USD
$30-250 AUD
₹750-1250 INR / hour
₹600-1500 INR
$15-25 USD / hour
₹8000-15000 INR
₹12500-37500 INR
$30-250 USD
₹600-1500 INR
₹1500-12500 INR
₹12500-37500 INR