
Closed
Posted
Paid on delivery
I am looking for an expert Electronics Design Engineer to review, optimize, and finalize a draft KiCad schematic for a custom, battery-powered audio logging device. The core architecture relies on an ESP32-S3-WROOM-1-N16R8-1U module paired with a TDK T5838 digital microphone featuring Acoustic Activity Detection (AAD). The device operates primarily in an ultra-low power standby mode: the ESP32-S3 stays in deep sleep with Wi-Fi completely turned off, while the TDK T5838 remains always-on to monitor the acoustic environment. When a sound trigger occurs, the microphone must wake the ESP32-S3 using an AAD interrupt (via D1, D2, or Analog AAD mode) to record audio onto a microSD card. The ESP32-S3 will wake up its Wi-Fi radio only during a specific, firmware-defined time window to transmit the recorded files. The system is powered by a 3.7V LiPo/Li-ion battery (capacities ranging from 2,500 mAh up to 10,000 mAh). There is also a 5V external input available for future deployment. Scope of Work & Deliverables 1. Power Entry Stage & Cold-Swap Protection • Remove Charging Circuit: Completely strip out the existing 3.7V battery charging subsystem. • Mechanical Footprint Update: Replace the current Surface Mount Technology (SMT) JST-PH 2.0mm battery connector with a robust, Through-Hole (THT) Right-Angle JST-PH variant to handle repeated structural stress during manual swaps. • Cold-Swap Mitigation: Design a protection stage (e.g., TVS diodes and adequate bulk capacitance) to absorb inrush current spikes, contact bounce, and voltage arcs caused by manual battery hot/cold swaps. • Reverse Polarity Protection: Implement a zero-loss or ultra-low-loss reverse polarity protection circuit (e.g., an appropriately rated P-Channel MOSFET or a dedicated ideal diode IC). Traditional silicon/Schottky diodes are unacceptable due to their forward voltage drop and wasted battery capacity. 2. Ultra-Low Power Optimization & Power Gating • Always-On vs. Gated Rails: Keep the TDK T5838 microphone and the ESP32-S3 RTC domain on an ultra-low quiescent current (\(I_{q}\)) always-on rail. • Peripheral Isolation: Implement load switches (e.g., low-leakage P-channel MOSFETs or dedicated load switch ICs like the TPS22917) to completely cut off power to the microSD card and its associated pull-up resistors when the system is asleep. • Component Benchmarking: Review the active Bill of Materials (BOM) and replace inefficient components (such as old AMS1117 LDOs) with ultra-low \(I_{q}\) voltage regulators (e.g., high-efficiency Buck-Boost regulators or nano-amp LDOs like the TPS7A02). 3. Signal Integrity, Impedance & Back-Current Prevention • Back-Current & Leakage Auditing: Ensure no digital lines or pull-up resistors leak parasitic current into unpowered peripherals or back-feed the ESP32-S3 pins during deep sleep. • Signal Validation: Confirm clean signal paths between the TDK T5838 (AAD D1/D2/Analog pins) and the ESP32-S3 RTC GPIOs, as well as the microSD SDIO/SPI lines. • Impedance/Resistance Checks: Verify that pull-up/pull-down values are optimized for low consumption while preserving edge-rate signal integrity. 4. Fuel Gauge / Battery Monitoring • Add a programmable, low-overhead circuit to monitor and read remaining battery capacity/voltage via firmware (e.g., using a high-impedance voltage divider switched via a MOSFET, or a dedicated ultra-low-power I²C fuel gauge IC). 5. Interface Overhaul (USB-C & 5V Input) • Replace 2-Pin 5V Connector: Replace the existing vertical 2-pin connector with an elegant, low-profile, sink-only USB Type-C connector for the 5V input. • USB-C Logic & OTG Functionality: Ensure CC1/CC2 lines are properly terminated with 5.1kΩ resistors so standard USB-C PD power bricks can power the board. The Native USB OTG lines of the ESP32-S3 must maintain flawless connectivity to a PC for flashing firmware and debugging. • Power Muxing: Ensure safe isolation between the 5V USB-C input and the 3.7V raw battery rail so they never back-feed or damage each other. Layout Consultation (Optional but Welcomed) • Provide a brief set of high-level recommendations or placement notes for the physical PCB layout (especially regarding audio signal traces, ground planes, and USB differential pairs), which I will be routing myself. Required Skills • High proficiency in KiCad Schematic Capture • Deep expertise in Ultra-Low Power (Micro-amp/Nano-amp) hardware design • Strong background with ESP32-S3 SoC systems and peripheral power management • If you read this sentence then message me with "Hello-World". And one important thing: If you are using some AI tool to generate the schema or to check the required above requirements then you are the wrong person for this job. • Experience with Digital Microphones (I2S/PDM/AAD) and high-speed data buses (microSD/SDIO) Regards, Sergiu
Project ID: 40768104
39 proposals
Remote project
Active 16 hours ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
39 freelancers are bidding on average $35 USD for this job

Hello-World Greetings, I’ve worked on low-power embedded systems including Qualcomm IoT hardware/firmware, ESP32-class devices, power management, sleep/wake behavior, and production PCB reviews, so this project is close to the kind of work I normally do. For this design, I think the main challenge is not just choosing low-Iq regulators, but making sure the always-on microphone can reliably wake the ESP32-S3 while the SD card and other peripherals are fully powered down without leakage or back-feeding. I would first review the complete KiCad schematic and BOM, check the power-tree, T5838 AAD wake path, USB-C/battery isolation, GPIO states and leakage paths, then make the required schematic corrections. For a board of this scope, I would expect to have the first detailed review and proposed changes ready within about 1–2 working days after receiving the KiCad project, BOM, and current power-consumption targets. Do you already have a measured or target standby current for the complete device? Sincerely, Oleksandr
$20 USD in 7 days
8.4
8.4

Hi, I have experience in designing Circuits and can complete your project. I have expertise in the following: 1- Designing schematic and PCBA 2- Ordering the PCBA and getting boards manufactured. 3- Writing firmware for the PCBA to make sure everything works as expected. 4- I can also develop smartphone apps to communicate and control the hardware. If you wish we can discuss in chat. Thank you.
$20 USD in 7 days
7.5
7.5

Hello-World Hi Sergiu, I have experience in ESP32 hardware design, KiCad schematics and low power battery systems. I can review and optimize your design, focusing on deep sleep consumption, battery protection, microSD power gating, AAD wakeup and USB-C power isolation. I will work on your existing schematic and check the components and datasheets carefully. Best regards.
$20 USD in 7 days
5.6
5.6

With your project's focus on optimizing the hardware of an ESP32-S3-based audio logging device, my extensive experience designing electrical systems and PCB layouts aligns seamlessly with your needs. I have a keen understanding of low-power design techniques and approaches that allows me to effectively address the key challenges you lay out in your project description. My familiarisation with components such as the TDK T5838 microphone featuring Acoustic Activity Detection (AAD), gives me valuable insights for ensuring signal integrity and impedance/resistance optimization. In addition to my expertise in hardware design, I bring comprehensive knowledge of embedded systems and microcontroller firmware development, especially with popular platforms like Arduino and STM32/ESP32. This will be invaluable in efficiently implementing the power gating you require for ultra-low-power operation, as well as addressing peripheral isolation through load switches.
$20 USD in 7 days
5.1
5.1

I am an Embedded Systems and PCB Design Engineer with experience in Altium Designer, Kicad, Easyeda, Protious and custom hardware development. I can design your PCB from schematic to production-ready files, including: • Schematic Design • PCB Layout • Component Selection • Design Rule Check (DRC) • Gerber Generation • BOM Preparation • Manufacturing Support (JLCPCB, PCBWay, etc.) I have experience with ESP32, STM32, sensor interfaces, power supplies, RF modules, Ethernet, and industrial electronics. Please share the project requirements, schematic (if available), board dimensions, and any special requirements. I can start immediately. Looking forward to working with you.
$120 USD in 7 days
5.1
5.1

Hi, Greetings! I am interested in working on your project. Could you please share the design details and technical requirements so we can discuss the project scope and key parameters in detail? I look forward to working with you. Thank you! Shivkant
$60 USD in 7 days
4.7
4.7

As a seasoned Electronics Design Engineer, I bring to the table not only comprehensive proficiency with KiCad but also valuable experience with power optimization and low power design strategies - two key pillars of your project. Moreover, my understanding of battery management, including analyzing, designing and implementing power entry stages and cold-swap protections will be pivotal in handling the Li-ion battery challenges your device encounters.
$35 USD in 1 day
5.1
5.1

As an experienced Electronics Design Engineer, I bring unique skills and capabilities that align perfectly with this project. My expertise in circuit design, electrical engineering, and PCB layout is extensive, encompassing various battery-powered devices with a flawless understanding of ESP32-S3 modules. I am especially proficient in using KiCad Schematic software, ensuring a thorough review, optimization, and finalization of such designs. Handling ultra-low power standby modes has always been my niche; my experience sets me perfect for optimizing your device's deep sleep mode while the TDK T5838 remains active recording audio. I am ready to execute cold-swap protection measures, ensuring no inrush current spikes or voltage arcs deter the device's performance during battery swaps. Implementing zero-loss reverse polarity protection is second-nature, sustaining optimal efficiency by eliminating forward voltage drops common with silicon or Schottky diodes. Moreover, my ultra-low power optimization strategy and power gating technique guarantees tremendous energy savings without compromising functionality. I'll replace old AMS1117 LDOs with more efficient voltage regulators like high-efficiency Buck-Boost regulators while also ensuring impeccable signal paths between the TDK T5838 and ESP32-S3 GPIOs.
$85 USD in 2 days
5.0
5.0

Hi Sergiu, Hello-World. I’m a PCB and hardware designer experienced in schematic design, power management, and embedded hardware. I can review and optimize your KiCad schematic, focusing on ultra-low-power operation, battery protection, power gating, USB-C connectivity, and peripheral back-power prevention. Please share the draft schematic and BOM so I can review the existing design and confirm the scope. Best wishes, Ahmed Yahia
$20 USD in 7 days
4.6
4.6

Hello-World Hello, I can help review your KiCad schematic with particular attention to ultra-low-power operation, safe power switching, and reliable ESP32-S3 peripheral interfaces. I’ll assess the battery input protection, reverse-polarity MOSFET design, always-on microphone rail, microSD power gating, and leakage paths that could compromise deep-sleep current. I’ll also review regulator selection, battery monitoring, USB-C CC termination, native USB connectivity, and power isolation between the battery and 5V input. The updated schematic will include clear component values, practical design notes, and a carefully checked BOM, with PCB placement recommendations for audio signals, grounding, and USB differential pairs. Please share your existing KiCad project and BOM so we can define the review scope and deliverables.
$12 USD in 7 days
4.5
4.5

As an Electronics Design Engineer with deep experience in electrical engineering and PCB layout, I am perfectly positioned to optimize your ESP32-S3 Audio Hardware to its fullest potential. My work on complex projects involving low-power design and hardware features aligns seamlessly with the scope of your project. My expertise stretches across crucial aspects you've outlined, from power entry stage design, through Ultra-Low Power Optimization & Power Gating, all the way to Signal Integrity and Back-Current Prevention. Whenever you mention specific feature requirements like reverse polarity protection or impedance checks, my many years in the field come to play to guarantee top-notch execution.
$45 USD in 1 day
3.9
3.9

As an RF and Electronics Engineer with a specialization in high-frequency systems and extensive experience in advanced electronic design, I am confident in my abilities to bring immense value to your ESP32-S3 Audio Hardware Optimization project. My skill set aligns precisely with the scope of work you've described, from power entry stage redesign to signal integrity auditing. My past projects involved similar tasks: ultra-low power optimization, impedance/resistance checks, and even fuel gauging and battery monitoring, which means I'm well-versed in navigating the challenges we'll encounter. Beyond just having the skills, I have a penchant for excellence. Because of my commitment to providing high-performance solutions for communication, radar, and embedded electronic applications, I am accustomed to the constant pursuit of optimization and efficiency. In fact, I actively keep myself updated on emerging trends and technologies that may enhance the design process. This is why I always advocate for both theoretical knowledge and practical implementation, ensuring our solutions are not only robust but also innovative. I believe my expertise coupled with my continuous pursuit of pushing boundaries in my field makes me the perfect fit for this project. Adaptable to various PCB tools like KiCad, Proteus, Altium designer including popular programming languages (C/C++) used on microcontrollers like Arduino and ESP series.
$30 USD in 7 days
2.5
2.5

As a highly experienced Electronics Design Engineer, with a strong background in embedded systems and circuit design, I am confident that I am the perfect fit for your ESP32-S3 Audio Hardware Optimization project. With over two decades in the tech industry, I have developed a deep proficiency in managing similar projects and honed my skills to expert levels. Critically addressing each point in your scope of work, here's what I bring to the table: I possess extensive knowledge in battery-powered devices optimization and have achieved remarkable results in power consumption reduction during sleep states. Implementing robust cold-swap protection systems is another area I excel at, having worked on various projects that involve manual battery swaps. Additionally, my work with signal integrity auditing ensures zero back-current leakage while guaranteeing clean connections between components. Acknowledging your emphasis on efficiency and low-power usage, I favor component optimization and load switching for cutting-edge performance optimization. My experience includes efficient BOM management and replacing outdated components like LDOs with ultra-low \(I_{q}\) voltage regulators to save battery utilization thus ensuring a dependable, long-lasting supply.
$10 USD in 7 days
2.2
2.2

With over five years of experience in electronics design and a repertoire of successful projects, I can guarantee you not just an exemplary job on your sophisticated ESP32 audio hardware optimization, but also solutions best-practiced for long-term availability and supply chain compatibility. End-to-end client satisfaction is my priority, so each design I deliver is meticulously thought out to balance thermal performance, reliability, manufacturability while employing the latest components in the market to maximally optimize system functionality. From ultracompact commercial drones to kinetic lights control - I've designed a variety of integrated hardware and software devices that demanded precision and power optimization- notable traits for this project. I'm highly conversant with ESP32 and well-familiarized with Arduino, STM32 platforms - ready to leverage this expertise to streamline your Bluetooth logging device for optimal energy usage. Combining my skills of Arduino, Circuit Design, Electronics, Embedded Systems, Microcontroller along with my proficiency in firmware development for microcontrollers including Arduino, ESP32 ensures I am the perfect fit for your project. Partnering with me for the ESP32-S3 Audio Hardware Optimization guarantees a sleek and robust design that optimizes both power consumption and user-experience fulfilling your bespoke needs. Dedication and satisfaction are guaranteed!
$50 USD in 7 days
0.0
0.0

Hello-World Hi Sergiu, I'm an electronics engineer specializing in circuit design and KiCad, with ESP32 experience. You can see my KiCad work in my portfolio. I'll review and update your schematic based on your list: power entry and protection, low-Iq regulator and power gating, sleep leakage checks, battery monitoring and USB-C input. You'll get the updated KiCad files, a revised BOM and short layout notes. Once I see the files I'll confirm the scope; the price includes one revision round. Could you send the current project files and your KiCad version? Also, which AAD mode do you plan to use (Analog, D1 or D2), and should THSEL be set in hardware or from firmware? Best regards, Amin
$30 USD in 4 days
0.0
0.0

Must meet ultra-low power and cold-swap safety: I will review and harden your draft KiCad schematic for an ESP32-S3 battery audio logger using TDK T5838 AAD wake (D1/D2/Analog), with Wi‑Fi off in deep sleep and radio enabled only during a firmware-defined transmit window. I’ll remove the existing charger subsystem, replace the SMT JST-PH 2.0mm with a THT right-angle JST-PH, and add ideal reverse-polarity protection (P‑MOSFET/ideal diode), plus TVS + bulk capacitance to absorb swap inrush/contact bounce without wasting headroom. I’ll then optimize power architecture: benchmark and replace LDOs like AMS1117 with nanoamp/efficient regulators, keep T5838 + ESP32 RTC domain always-on, and add low-leakage load switches to fully cut microSD rails/pull-ups during sleep. I’ll audit back-current/leakage paths through GPIO pull-ups and AAD routing, confirm microSD SDIO/SPI signal integrity, and ensure no parasitic feed into unpowered peripherals.
$20 USD in 7 days
0.0
0.0

Step 1: I audit your current KiCad draft end-to-end—power entry, wake/interrupt path (TDK T5838 AAD D1/D2/Analog to ESP32-S3 RTC GPIO), microSD gating, and any backfeed risks on sleep pins. Step 2: I redesign the battery stage by removing the charging circuit, switching the JST-PH battery connector to robust THT right-angle, and adding cold-swap protection (TVS + bulk capacitance) plus ideal-diode reverse polarity using a P-MOSFET/ideal-diodes IC (no lossy Schottkys). Step 3: I optimize ultra-low power: select nano-amp/quiescent regulators (replace AMS1117), keep mic + RTC always-on, and fully power-cut microSD via low-leakage load switches (TPS22917-class). Step 4: I verify signal integrity (pull values, SDIO/SPI edges, leakage into unpowered rails). Step 5: I add a programmable fuel-gauge strategy (switched divider or low-Iq I2C). Step 6: I update USB-C sink-only 5V with proper CC 5.1kΩ and clean power muxing from battery.
$20 USD in 7 days
0.0
0.0

KiCad schematic audit: ERC/DRC strategy, net-class + constraint review, and power-tree verification with load-switch/load-leakage checks. I’ll map ESP32-S3 deep-sleep domains, TDK T5838 always-on AAD wake (D1/D2/Analog), and microSD power gating into a clean, battery-first architecture. Methods: quantify quiescent paths, back-feed/leakage tracing, and connector/power transient design for real hot-swap behavior. Deliverables: remove the 3.7V charging subsystem; redesign battery entry with THT right-angle JST-PH, zero-loss ideal-diode reverse protection (no Schottky loss), and cold-swap mitigation using TVS + bulk capacitance sized for inrush/contact bounce. Optimize power rails: replace AMS1117-class parts with nanoamp-class regulators/load switches (e.g., TPS22917-class), ensure RTC/mic rails remain always-on while microSD and pull-ups are fully disconnected.
$20 USD in 7 days
0.0
0.0

Cold-swap safety and true nanoamp standby performance are the highest-risk parts: a battery hot-swap must not back-feed rails or spike the ESP32-S3, while the TDK T5838 AAD path must wake reliably from the RTC domain with Wi‑Fi fully off. My approach (Daniel Gutierrez) focuses first on power-entry redesign, then on rail gating/leakage audits across microSD, AAD GPIOs (D1/D2/Analog), and SDIO/SPI. I’ll remove the charging subsystem, replace the SMT JST-PH with a THT right-angle JST-PH, and add reverse-polarity protection using an ideal-diode/P‑MOSFET style circuit plus TVS/bulk capacitance for inrush, bounce, and arc absorption. Next: swap AMS1117-class parts for ultra-low-Iq regulators, use load switches (e.g., TPS22917-class) to fully cut microSD pullups during deep sleep, and verify back-current prevention on every unpowered peripheral pin state. Finally, I’ll add a low-overhead fuel-gauge plan (Hi‑Z divider+MOSFET or I²C gauge), validate USB‑C CC1/CC2 5.
$20 USD in 7 days
0.0
0.0

KiCad schematic optimization workflow; KiCad ERC/DRC pass, netclass rules, and footprint sanity checks; power integrity review with LTspice-style calculations; low-Iq audit for regulators/switches; ESP32-S3 deep-sleep wake/RTC GPIO validation; microSD backfeed/SDIO isolation analysis; USB-C CC termination verification (5.1k). I’ll revise your draft KiCad schematic for the ESP32-S3-WROOM-1-N16R8-1U + TDK T5838 (AAD wake via D1/D2/Analog). I’ll remove the charger section, update the battery connector footprint to THT right-angle JST-PH, and add cold-swap mitigation (TVS + bulk capacitance sized for contact bounce/inrush). Reverse polarity will be implemented with an ideal-diode/PN MOSFET approach (no Schottky/Si loss). Next, I’ll harden ultra-low power: keep T5838 + RTC domain always-on, fully power-gate microSD and pull-ups with low-leakage load switches (e.g., TPS22917-class), and replace AMS1117-like parts with nanoamp/high-efficiency options (TPS7A02-class).
$20 USD in 7 days
0.0
0.0

Iași, Romania
Payment method verified
Member since Oct 5, 2026
$30-250 USD
$30-250 USD
₹12500-37500 INR
$10-30 USD
£20-250 GBP
$30-250 CAD
$1500-3000 USD
₹600-800 INR
₹12500-37500 INR
₹1500-12500 INR
₹1500-12500 INR
$750-1500 USD
₹600-1500 INR
$30-250 NZD
$30-250 USD
£10-20 GBP
$250-750 USD
$30-250 USD
$30-250 USD
$10-30 USD
€750-1500 EUR