
In Progress
Posted
Paid on delivery
Status: Schematic is finalized — layout work only (with expert schematic/BOM review). Project Overview I need an experienced PCB designer to create the PCB layout for a small precision encoder module with Bluetooth Low Energy (BLE) connectivity. The complete electronic schematic and BOM are already defined; your task is the board layout, design review, and preparation of full manufacturing data. A schematic review is required to confirm correctness before placement begins. Board Architecture: The board contains two functionally independent sections, which must be physically separated to avoid mutual interference: - Encoder section: STM32G474 microcontroller and its supporting peripherals, two AM26LV32E differential line receivers and ESDA6V1SC6 ESD protection device. - Bluetooth section: EBYTE E73-2G4M08S1CX BLE module (nRF52840-based, pre-certified) — the IPEX/[login to view URL] antenna connector is integrated into the module itself, so no antenna connector needs to be placed on the PCB, supporting peripherals and USBLC6-2SC6 ESD protection device (on USB lines). No RF/antenna design is required. Standard good practice applies: maintain solid ground under the module per the EBYTE reference layout, keep the antenna connector area clear of obstacles at the board edge (the external antenna connects directly to the module), and keep noisy encoder signals routed away from the BLE section. Design Requirements: - Layers: 4-layer [layer stackup — e.g., SIG / GND / PWR / SIG] - Dimensions: 40 mm × 60–80 mm - Placement: Encoder and BLE sections placed in clearly separated areas of the board. - Components: All SMD; the only through-hole part is the 5-pin programming connector. Inputs I Will Provide: - Altium schematic (also as PDF) and BOM - Netlist - Mechanical outline of the enclosure/module - Datasheets for requested components (MCU, BLE module, receivers, ESD parts) Please confirm receipt and completeness of these inputs before starting component placement. Flag anything missing immediately. Design Review: Before layout begins, perform an expert review of the schematic and BOM and report any errors (footprint mismatches, wrong part numbers, electrical issues, missing decoupling, etc.). I will confirm or correct findings before you proceed with placement. Deliverables (board ready for ordering and assembly): - Fully editable Altium project files (schematic + PCB, including libraries/footprints used) - Manufacturing package: Gerber files, NC drill files, solder mask layers - Assembly package: Pick-and-Place (component placement) file - Updated BOM reflecting any footprint or part-number changes made during review/layout
Project ID: 40758923
38 proposals
Remote project
Active 14 hours ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs

Hello, Your STM32G474 + E73 BLE board needs more than just clean routing. The critical points are differential encoder signal integrity, correct receiver termination, ESD protection, and keeping switching/digital noise away from the BLE section. Before placing components, I would review the Altium schematic and BOM, particularly: - AM26LV32E input termination, signal polarity, and protection. - STM32G474 power pins, decoupling, reset, and programming connections. - E73 module supply filtering, reference layout, and antenna connector clearance. - Footprint accuracy, component availability, and mechanical constraints. For the 4-layer PCB, I would maintain a continuous ground reference, separate the functional sections through placement and routing, and verify the layout against manufacturing rules. **Three questions before starting:** 1. What is the encoder's maximum signal frequency and cable length? 2. Are the receiver termination resistors already included in the schematic? 3. Does your Altium project include the component libraries and approved PCB stack-up? I can deliver the editable Altium project, reviewed BOM, Gerbers, drill files, and Pick-and-Place data. I suggest starting with a schematic/BOM review milestone so any issues are resolved before PCB placement. Best regards, Hamza El Amraoui
$100 USD in 6 days
2.8
2.8
38 freelancers are bidding on average $101 USD for this job

Hi, I am an embedded systems engineer with over 16 years of experience. I have extensive experience designing compact Altium boards for precision sensing and motion control, including STM32-based electronics alongside BLE modules, and preparing designs for production. I will first confirm that your schematic, BOM, netlist, mechanical outline and datasheets are complete and flag anything missing. I will then review the schematic and BOM for electrical issues, decoupling requirements and footprint or part-number mismatches, and wait for your confirmation of the findings before starting placement. For the four-layer layout, I will keep the encoder and Bluetooth sections physically separated, maintain suitable grounding and follow EBYTE's reference layout, with clear access around the module's integrated antenna connector. I will deliver the editable Altium schematic and PCB project with all libraries used, Gerbers including solder mask, NC drill files, pick-and-place data and an updated BOM, after final design-rule checks. Is the final board length fixed by the enclosure, and do you have a preferred PCB manufacturer? My $150 bid is above the listed budget to cover the expert review, four-layer layout and complete manufacturing handover. I am flexible and can discuss the budget with you. Please contact me to discuss details.
$150 USD in 7 days
7.6
7.6

Hi, I have experience in designing Circuits and can complete your project. I have expertise in the following: 1- Designing schematic and PCBA 2- Ordering the PCBA and getting boards manufactured. 3- Writing firmware for the PCBA to make sure everything works as expected. 4- I can also develop smartphone apps to communicate and control the hardware. If you wish we can discuss in chat. Thank you.
$75 USD in 7 days
7.5
7.5

Hello, I can review your Altium schematic and BOM first, checking component part numbers, footprints, decoupling, power integrity, and electrical issues before starting placement. I will design the 4-layer PCB within your 40 mm × 60–80 mm constraints, keeping the STM32G474 encoder circuitry physically separated from the BLE module and its sensitive RF area. I will follow the EBYTE reference layout, maintain a solid ground plane, and route noisy encoder signals away from the BLE section. I will confirm receipt and completeness of all inputs and flag missing information before placement begins. Deliverables will include the editable Altium project, libraries/footprints, Gerber and NC drill files, solder mask layers, pick-and-place file, and updated BOM. Regards, Engr Muhammad Usman
$175 USD in 7 days
6.9
6.9

As an experienced PCB designer with a strong background in electrical engineering, circuit design, and electronics, I believe my skills and expertise align perfectly with the requirements of your project. With proficiency in multiple software like Altium, as well as a thorough familiarity with STM32G474 microcontroller and components like AM26LV32E receivers and ESDA6V1SC6 ESD protection device, I can not only deliver a perfect board layout design but also conduct a diligent review of your schematic and BOM to ensure everything is error-free before proceeding. I understand the importance of maintaining separate areas for different sections within a PCB to avoid interference. I also am well-versed with the standard best practices you mentioned - keeping noisy encoder signals segregated from BLE section, providing solid ground under the Bluetooth module while keeping the antenna connector area clear - all crucial tasks to be taken care of while designing this precision encoder module. This attention to detail combined with my solid understanding of PCB architecture enforces my suitability for the job.
$100 USD in 2 days
6.6
6.6

Hello, I’m an Electronics and PCB Design Engineer experienced in STM32-based embedded systems, multilayer PCB layout, and manufacturing-ready designs. I can review your schematic and BOM before placement, checking component part numbers and footprints, power integrity, decoupling, ESD protection, and potential electrical issues. For the 4-layer, 40 × 60–80 mm board, I’ll focus on: * Clear physical separation between the encoder and BLE sections. * Solid ground reference and proper power distribution. * Routing of differential encoder signals with controlled return paths. * Following the EBYTE reference layout and keeping the BLE antenna area clear. * USB ESD protection, design-rule checks, and manufacturing optimization. Deliverables will include the editable Altium project with libraries, Gerber and NC drill files, assembly pick-and-place data, and an updated BOM. I’ll first verify that all supplied files are complete, document any schematic/BOM issues, and wait for your approval before starting component placement. Please share the schematic, BOM, netlist, mechanical outline, and component datasheets so I can begin the review.
$75 USD in 7 days
5.6
5.6

Hi, how are you doing? I went through your project description and I can help you in your project. your project requirements perfectly match my expertise. We are a team of Electrical and Electronics engineers, we have successfully completed 1000+ Projects for multiple regular clients from OMAN, UK, USA, Australia, Canada, France, Germany, Lebanon and many other countries. We are providing our services in following areas: Antenna Design (CST, HFSS) Embedded C Programming. VHDL/Verilog, Quartus/Vivado, LabVIEW/ Multisim/PSPICE/VLSI MATLAB/SIMULINK Network Simulator NS2/NS3 Microcontroller like Arduino, Raspberry Pi, FPGA, AVR, PIC, STM32 and ESP32. IDEs like Keil MDK V5, ATmel studio and MPLab XC8. PLCs / SCADA PCB Designing Proteus, Eagle, KiCAD and Altium IOT Technologies like Ethernet, GSM GPRS. HTTP Restful APIs connection for IOT Communications. Also, we have good command over report writing, I can show you many samples of our previous reports. Kindly consider us for your project and text me so that we can further discuss specifically about your project's main goals and requirements.
$75 USD in 7 days
6.2
6.2

Hello Layout-only job on a finalized schematic: 4-layer 40×60–80 mm encoder board with the STM32G474 and AM26LV32E encoder section kept cleanly apart from the EBYTE E73 BLE section. With 15+ years of experience, I focus not only on developing the electronics and firmware, but also on making the overall development process clear, practical, and reliable for the client. I designed the 1-Wire/I2C-to-RS485 converter PCB in Altium from schematic review through the assembly package. Process: Confirm receipt of your inputs — Altium schematic, netlist, mechanical outline, datasheets — and flag anything missing before placement begins. Expert schematic/BOM review first: footprint mismatches, wrong part numbers, missing decoupling, electrical issues — reported for your confirmation before I place a single component. Placement and routing on SIG/GND/PWR/SIG, solid ground under the EBYTE module per its reference layout, antenna connector area kept clear at the board edge, encoder signals routed away from the BLE section. Deliverables: editable Altium project with libraries/footprints, Gerber + NC drill + mask package, pick-and-place file, and updated BOM reflecting any review changes. Best regards, Hamza
$75 USD in 7 days
5.4
5.4

I’ve reviewed the requirements for your Precision Encoder + BLE module. Designing a board that balances a noisy encoder section with an RF-sensitive BLE module is a challenge I enjoy, and I have a clear plan to handle the isolation and grounding requirements (especially respecting the EBYTE reference layout). My focus is on delivering a production-ready board. To that end, my process includes: Critical Review Phase: Deep-dive analysis of your current schematic and BOM to fix issues before placement. Layout & Routing: Strategic placement to ensure the encoder signals stay well away from the BLE path, maintaining a clean 4-layer stackup. Full Documentation: Delivering everything from editable Altium files to Gerber/Assembly packages so your manufacturer has zero questions. I am ready to start as soon as you share the input files. Looking forward to hearing from you.
$100 USD in 20 days
5.4
5.4

As an accomplished PCB designer with extensive experience in circuit design and electrical engineering, I believe I possess the precise skill set necessary for your project. With proficiency in electronic design, electronics, and a specialization in STM32, I'm equipped to expertly address the unique demands of your schematic and design outlined. To ensure maximum efficiency even before component placement, I will perform a vigilant review of your schematic and BOM. Having maintained a keen eye for detail throughout my career, I will not only identify any footprint mismatches or potential electrical issues but also recommend optimized design changes, guaranteeing superior functionality. My goal is to deliver a board layout that grants you seamless Bluetooth connectivity alongside top-notch precision encoder capabilities. Apart from my design abilities, my competencies extend to full IoT implementation and device manufacturing. This project's stack of Bluetooth Low Energy (BLE) module with an integrated antenna maps on to my proficiency with MQTT-connected sensor networks - a fitting foundation for successful completion of your project! Combining this with my comprehensive software know-how (AWS/GCP/Azure), deploying your final product will be painless. Hence, hiring me guarantees not only exceptional PCB layout but also smooth integration to the final ECM workflows.
$120 USD in 7 days
5.1
5.1

HI, I am an experienced electronics and PCB Design engineer, specialised in use of ECAD software such as Altium Designer, KICAD, EasyEDA, etc. for the the design of electronics and PCB. I will design your projects to meet your Requirements and the industry standard. I do all kinds of circuits such as Power delivery circuit, Sensor Integrated Circuits, wireless control, MCUs etc. I will deliver the following. The Schematics for your Design The PCB for the design Bill of materials(If needed) Gerber, Pick and Place and other manufacturing and assembly drawings needed. Full Support and consultancy till the project is done. Kindly send me message for my previous designs and also so we can discuss further on your project I look Forward to working with you. Best Regards, Abdur-Rafiq
$75 USD in 7 days
5.3
5.3

Hi, I’ve carefully read and understood the requirements. I have hands-on experience with Altium, 4-layer PCB design, STM32, BLE modules, differential signals, and ESD protection. I can review the schematic and BOM first, verify footprints and critical connections, then design the PCB with proper separation between the encoder and BLE sections, grounding, decoupling, and manufacturing checks. I’ll deliver the editable Altium project, Gerbers, drill files, pick-and-place, and updated BOM. You can also check my portfolio for my previous 4-layer PCB projects. Best regards, Ahmed
$75 USD in 7 days
4.6
4.6

I have experience in PCB design using Altium Designer, including schematic development, component placement, and precise PCB routing. I focus on reliable signal connections, noise reduction, design rule checks (DRC), and manufacturing-ready files. I can help develop a precision encoder PCB with accurate signal routing, a well-organized layout, and complete fabrication documentation. You've got the schematic locked and just need the layout done right — that's exactly where I'm useful. I'll review your Altium schematic and BOM first, flag any footprint mismatches or missing decoupling, then route the 4-layer board with encoder and BLE sections cleanly isolated. → I've shipped 4-layer STM32 and nRF52840 boards with mixed-signal and BLE sections, keeping noisy encoder signals clear of the RF module. → Deliverables: editable Altium project, Gerbers, NC drill, pick-and-place, and updated BOM. → I'll confirm your inputs are complete before placement and flag anything missing immediately.
$60 USD in 3 days
3.2
3.2

At HardFault, we see the need for precision and reliability in your precision encoder module with Bluetooth Low Energy connectivity. With the schematic and BOM finalized, our team is well-prepared to deliver an expertly reviewed and thoroughly checked board layout. Our expertise in custom PCB design, particularly in embedded hardware for industrial IoT devices, resonated with the needs of this project. We have considerable experience in working with STM32 microcontrollers and BLE modules, ensuring that the two functionally independent sections of your board will be designed with meticulous attention to interference avoidance and signal integrity. Our team, as opposed to a solo freelancer, offers a broader range of skills and redundancy, ensuring both a faster turnaround and comprehensive error checking. We will start by conducting a rigorous review of the provided schematic and BOM to address any discrepancies before proceeding with the layout, keeping communication clear and proactive throughout. We're curious, what specific challenges do you foresee in terms of the mechanical constraints or interfacing with existing systems that we should keep in mind?
$105 USD in 10 days
3.1
3.1

As a seasoned Freelancer with a strong background in embedded systems engineering and a comprehensive understanding of electronic product development, I am confident that I can bring crucial knowledge and expertise to your PCB design project. With an excellent track record in meticulously planning and building the entire spectrum of electronic products, from initial schematicing to final device functionality, I emphasize seamless integration between hardware and software elements, minimizing redundancies whilst maximizing efficiency. My ability to dexterously manage every phase of the process also ensures minimal roadblocks along the way. Having already designed PCBs employing ESP32, nRF52, STM32, LTE/Wi-Fi modules among others, I have extensive familiarity with different elements vital for your project. Your design's precise demarcation requirements won't be treated lightly; my meticulous attention to detail will guarantee distinctly separated areas for each independent section—avoiding potential interference issues while maintaining best practices for ground patterns and signal routing.
$150 USD in 7 days
2.8
2.8

Greetings Dear Hiring Manager I can deliver your 4 layer Altium PCB layout with schematic review BLE isolation and manufacturing files 1. Are the Altium schematic and BOM finalized? 2. Can you share the enclosure outline and netlist? 3. Is the 40 mm board width fixed? 4. Are all component footprints already verified? 5. What placement and routing revision limits apply? Best Regards Dr Kainat
$50 USD in 1 day
1.8
1.8

I regularly design precision mixed-signal and BLE-enabled embedded hardware in Altium Designer, with direct experience implementing STM32G4-series microcontrollers and nRF52-based wireless modules. Translating your finalized schematic into a quiet 4-layer layout requires strict physical partitioning, low-impedance ground returns, and clean isolation between the fast-switching encoder differential receivers and the EBYTE BLE module. Upon receiving your Altium project, mechanical outline, and BOM, I will immediately verify input completeness and run a comprehensive pre-layout review. This includes auditing footprint-to-land patterns, pin mapping, decoupling loop paths, and ESD clamp topologies (USBLC6-2SC6 and ESDA6V1SC6) to flag any issues for your sign-off before freezing placement. For the layout, I will configure a balanced 4-layer stackup (SIG/GND/PWR/SIG) with an unbroken ground plane on Layer 2, route the AM26LV32E differential pairs with controlled impedance away from wireless circuitry, and observe proper module edge keepouts and solid ground stitching beneath the E73 module per manufacturer guidelines. Deliverables include native Altium Designer project files, integrated libraries, RS-274X Gerbers, NC drill data, pick-and-place CPL files, an updated BOM, and 3D STEP models for mechanical enclosure verification.
$195 USD in 5 days
0.9
0.9

I have solid experience in PCB design and layout, including 4-layer boards, STM32-based circuits, BLE/RF modules, differential signal routing, ESD protection, power distribution, grounding, and design-for-manufacturing. I am also familiar with reviewing schematics and BOMs before layout to identify footprint mismatches, incorrect part numbers, missing decoupling components, and other potential electrical or manufacturing issues. For this project, I can carefully separate the encoder and BLE sections, maintain a clean ground structure, route sensitive and noisy signals appropriately, and follow the module manufacturer’s layout recommendations. I can also prepare the complete Altium design files, Gerber, NC Drill, Pick-and-Place, and updated BOM so the board is ready for manufacturing and assembly.
$100 USD in 7 days
0.4
0.4

I DON'T COMPETE ON PRICE. I COMPETE ON RESULTS. lets talk with facts, actions and implementation. I specialize in creating high-quality PCB layouts for advanced electronic modules, ensuring they meet precise specifications and functionality. Your project requires a clean and professional layout while maintaining separation between the encoder and Bluetooth sections to avoid interference. I understand that this is crucial for optimal performance. With extensive experience in Altium and a solid grasp of best practices for multi-layer designs, I can ensure that your PCB layout is executed flawlessly, adhering to all specified guidelines. I would love to discuss your upcoming projects with you and answer any questions you may have. Kind Regards, Stacey
$50 USD in 14 days
0.0
0.0

I can help turn your requirements into a professional, reliable solution tailored to your needs. My focus is on delivering practical, user-friendly solutions with clean execution, strong functionality, and attention to detail. For your PCB Design for the Precision Encoder Module with Bluetooth, I can help with the expert schematic and BOM review to ensure the final result aligns with your goals. I will ensure proper separation of the encoder and BLE sections while adhering to best practices for layout and grounding. I'd be happy to discuss your requirements, answer any questions, and outline the best approach for your project. Regards, jamesh920
$100 USD in 7 days
0.0
0.0

Hi, Looking for an experienced technology partner to turn your concept into a reliable, production-ready product? We can help. Greetings from OSTronik India, we are specializing in Power Electronics, PCB Design, Embedded Systems, Firmware, IoT, AI Integration, and Mobile Application Development. Our Expertise ⚡ Power Electronics DC-DC & AC-DC converters, power supplies, power management, voltage/current regulation, protection, isolation, switching circuits and customized power solutions. ? PCB & Hardware Multilayer PCB design, schematic development, component selection, BOM preparation, Altium Designer, EMI/EMC considerations and production-ready files. ? Embedded & Firmware STM32, ESP32/ESP8266, PIC, AVR, Raspberry Pi, Embedded C/C++, sensor interfacing, hardware integration, debugging and optimization. ? IoT & Communication UART, SPI, I²C, CAN, RS-485, Modbus, MQTT, Wi-Fi, BLE, LAN, cloud connectivity and real-time monitoring. ? Mobile Applications Custom Android & iOS applications for device control, monitoring and data visualization. We can take your project from concept → design → prototype → testing → production, with a focus on reliability, performance and cost efficiency. Share your requirements or existing files, and let’s discuss how we can bring your product to life. Best Regards, Team OSTronik India Empowering Innovations
$75 USD in 7 days
0.0
0.0

Tokyo, China
Payment method verified
Member since Sep 20, 2026
$250-750 USD
$250-750 USD
₹1500-12500 INR
€30-250 EUR
$250-750 USD
€750-1500 EUR
$25-50 CAD / hour
₹37500-75000 INR
₹12500-37500 INR
$8-15 USD / hour
€30-250 EUR
₹10000-15000 INR
$250-750 USD
$250-750 NZD
₹9999-10000 INR
₹12500-37500 INR
₹12500-37500 INR
₹600-1500 INR
$30-250 USD
€250-750 EUR