Immediate PCB Power Board Design

@amelectronics

I am a skilled and reliable Embedded Systems Engineer with over 6 years of hands-on experience in Arduino, ESP32/ESP8266, and microcontroller-based development. I specialize in designing efficient, stable, and scalable embedded solutions, turning ideas into fully functional hardware-software systems. I have a strong background in electronics, sensors, communication protocols (UART, I2C, SPI, MQTT, WiFi, BLE), and real-time embedded systems. My development approach focuses on clean, well-structured, and well-documented firmware, ensuring long-term reliability and easy maintenance. I also provide thorough testing, debugging, and performance optimization, including power efficiency improvements where required. I am a detail-oriented engineer with strong problem-solving skills and extensive experience in hardware debugging and firmware optimization. Beyond technical expertise, I value clear communication, meeting deadlines, and maintaining high client satisfaction. I work closely with clients to fully understand project requirements and deliver high-quality results. Pricing is flexible and can be discussed based on project scope and complexity. I am open to both short-term and long-term projects. Let’s work together to build a professional, reliable, and efficient embedded system for your needs.

@Adeel2k14

Hello, I can start immediately and deliver the first pass within 3 days. I am an Electrical Engineer with 7+ years of PCB design experience, currently working as an Embedded System Design Engineer in a reputed firm. I have strong expertise in power management, low-noise regulator design, thermal optimization, and JLCPCB-ready layouts. I have designed up to 8-layer mixed-signal, high-speed, analog, and power boards, so maintaining tight DFM, clean routing, and ±2% regulation targets is well within my scope. I will provide KiCad schematic, PCB, 3D STEP, full manufacturing package, and design notes. Ready to begin.

@BOSIREX

I’m an experienced power-electronics PCB designer and can start immediately on your two-layer KiCad power-management board. I will design high-efficiency, low-noise regulator stages sized for 1 A load per rail, with proper component selection, ripple analysis, thermal calculations (copper area, via stitching, and junction temperature estimates), and clearly defined test points. The layout will be optimized for clean current return paths, tight feedback routing, controlled thermal rise, and DFM-ready clearances suitable for quick fabrication at JLCPCB or PCBWay. You’ll receive the full KiCad schematic, completed PCB layout within your 60 mm × 40 mm envelope, 3D STEP export, and a clean manufacturing package (Gerbers, drills, pick-and-place, BOM), plus a concise design note explaining regulator choices and validation approach. I will share progress screenshots/PDFs during routing and ensure ERC/DRC pass with zero errors. First-pass delivery in 3 days is achievable. If this evaluation goes well, I’d be glad to support your upcoming mixed-signal and embedded designs.

@hayat38402

Hi, how are you doing? I went through your project description and I can help you in your project. your project requirements perfectly match my expertise. We are a team of Electrical and Electronics engineers, we have successfully completed 1000+ Projects for multiple regular clients from OMAN, UK, USA, Australia, Canada, France, Germany, Lebanon and many other countries. We are providing our services in following areas:  Embedded C Programming.  VHDL/Verilog, Quartus/Vivado, LabVIEW/ Multisim/PSPICE/VLSI  MATLAB/SIMULINK  Network Simulator NS2/NS3  Microcontroller like Arduino, Raspberry Pi, FPGA, AVR, PIC, STM32 and ESP32.  IDEs like Keil MDK V5, ATmel studio and MPLab XC8.  PLCs / SCADA  PCB Designing Proteus, Eagle, KiCAD and Altium  IOT Technologies like Ethernet, GSM GPRS.  HTTP Restful APIs connection for IOT Communications. Also, we have good command over report writing, I can show you many samples of our previous reports. Kindly consider us for your project and text me so that we can further discuss specifically about your project's main goals and requirements.

@manusharma2992

Hi mate, When i seen the details "Immediate PCB Power Board Design" which you are searching. I am super exited to start it ASAP! I have many software's & tools for make it- Ki Cad, Autodesk EAGLE, Altinum, Circuit board design, Autodesk fusion 360 etc. Make 2d & 3d both I will share update within it in 1-2 Hours. Portfolio link - https://www.freelancer.com/u/manusharma2992 Sincerely Manu R.

@dcornelius7

Good day I am a hardware and firmware developer with experience developing DC-DC power supply circuits within my embedded PCBs to power GSM/BLE/WIFI modules utilized on the PCB, I am able to design your PCB using Altium, KiCad or Eagle, feel free to message me to discuss your project in finer detail

@TingWang250617

Hi, I'm very glad to have an opportunity to help you with PCB design. This job is very appealing to me because I have a lot of experience in PCB design of various kinds of the electronic devices. Especially, IoT devices I also have enough experience in high speed multi-layer routing and RF impedance control. I'm very familiar with Altium, Eagle and KiCAD. I have my own Altium license and Eagle license. So if you hire me, I can start work immidiately. Also, I have 5+ years experience in developing an FW for various MCU such as STM, PIC, Atemga, ESP etc. I'll provide you all design files and manufacturing files (part library, schematic, layout, BoM, pnp, ODB++, assembly document, gerber, DRC document, and 3d model) Also, I can support you for PCB manufacturing and PCBA from our local company(READA company) in Shenzhen, China if you want. We will provide high-quality in PCB manufacturing and PCBA, reliable part sourcing, functional test according to customer's specifications, and quick shipping. Also, I can help you to order PCBs from JLCPCB, PCBWay and SEEEDStudio if you want. I'm confident my skills and experience in PCB design make me a good candidate for your job. Looking forward to hearing from you soon. Kind Regards. Ting

@electronicsdone

Best High-Efficiency PCB Design Expert ⭐⭐⭐⭐⭐ Hi, Thank you for posting your project, “Immediate PCB Power Board Design.” I’ve reviewed your requirements for the compact power management board and am ready to deliver a high-efficiency, 2-layer KiCad design that meets your strict noise and thermal targets. I bring 11+ years of experience in DC-DC power regulation, thermal management, and rapid prototyping. I specialize in low-noise power distribution for consumer electronics, ensuring that regulator selection and copper pours are optimized for stability under load and minimal heat rise within tight mechanical envelopes. ✅ How I’ll Help You Succeed: 1. High-Efficiency Power Routing: I will design the regulated rails with optimized trace widths and polygon pours to ensure less than 2% voltage drop under 1A loads. 2. Real-Time Collaboration: I will share daily progress screenshots and PDFs of the layout, ensuring that footprints and test points align with your prototype requirements from day one. ✅ One Quick Question Before We Begin: What is your primary input voltage, and do you have a preference for switching regulators (for efficiency) or LDOs (for ultra-low noise) on your specific output rails? Best regards, Prat PCB Must Innovations

@abdurRafiqM

HI, I am an experienced electronics and PCB Design engineer, specialised in use of ECAD software such as Altium Designer, KICAD, EasyEDA, etc. for the the design of electronics and PCB. I will design your projects to meet your Requirements and the industry standard. I do all kinds of circuits such as Power delivery circuit, Sensor Integrated Circuits, wireless control, MCUs etc. I will deliver the following. The Schematics for your Design The PCB for the design Bill of materials(If needed) Gerber, Pick and Place and other manufacturing and assembly drawings needed. Full Support and consultancy till the project is done. Fell free send me message so we can discuss further on your project I look Forward to working with you. Best Regards, Abdur-Rafiq

@Bhartifreelancer

Hi there, I also possess a unique skill set for this project. Throughout my career, I've worked on numerous electrical engineering projects involving PCB design and layout much like this one. I'm highly skilled in using specialized software such as KiCad which is the preferred choice for this project. Despite my limited experience with delivering manufacturable packages for fabrication, I’m confident that with my technical acumen and excellent problem-solving skills, I’ll be able to swiftly navigate through any challenges that may arise. Additionally, meeting strict timelines, staying connected to you during the process and offering regular updates have always been central to my work ethic which aligns perfectly with your project requirements, ensuring a smooth collaboration. Best regards Bharti

@alishba438

I will do:- Simple to advanced Circuit design and analysis using software tools such as KiCAD, Proteus, Altium Designer, Allegro, PADs, and Eagle My package provides the following services - Schematic drawings - Gerber files - Netlist generation - Pcb's - BOM generation (Professional BOM) - 3D Models of the Actual PCB - ECAD Library Administration I will also generate Gerbers on existing PCBs files

@mohammadusman45

Hello Muhammad Usman here experienced Hardware developer. I am interested in this project as it really matches with my skills and expertise. Regards Muhammad

@engrhasan01

Hi, I’m an experienced Electronics Engineer specializing in power electronics, PCB design, and embedded hardware development. I can design your compact two-layer power management board in KiCad with a strong focus on efficiency, low noise, and thermal reliability within the 60 mm × 40 mm constraint.I will deliver a clean schematic, optimized PCB layout, 3D STEP export, and complete manufacturing package (Gerber, drill, pick-and-place, BOM). Regulation accuracy (±2% at 1 A) will be validated through simulation and proper compensation design. The layout will follow DFM best practices for seamless JLCPCB or PCBWay fabrication. I can provide the first-pass design within three days.

@joaquinc48

✅✅✅ Power Electronics PCB Designer (KiCad – 2 Layer) ✅✅✅ Hi there, I have strong experience designing compact power-distribution boards using high-efficiency buck/LDO regulators with low-noise and controlled thermal rise. I’ve delivered 2-layer consumer prototypes optimized for JLCPCB/PCBWay with clean DRC/ERC, solid grounding, and reliable 1A-class rails. My approach is to select regulators based on efficiency, ripple, and thermal headroom, simulate load performance (±2%), then implement tight loop layout, proper copper pours, thermal vias, and test points. I’ll share layout progress screenshots and deliver full manufacturing files plus a concise design note. A few questions: What input voltage range? How many rails and target voltages? Any sensitive analog loads requiring extra filtering? I can deliver a first pass within 3 days and am ready to start immediately. Best regards

@MADTechUK

Hi there, I'm excited about the opportunity to design your compact, two-layer PCB for reliable power management. With extensive experience in electrical engineering and PCB design, I have successfully delivered similar projects utilizing high-efficiency voltage regulators, ensuring low noise and thermal rise. I will leverage tools like KiCad to provide you with a precise schematic and PCB layout, ensuring we meet your targets of a 60 mm × 40 mm envelope and ±2% voltage stability under load. I understand the importance of speed and transparency in this evaluation, so I’ll share incremental updates via screenshots or PDFs, ensuring adherence to clean design practices. I can start immediately and will aim for a three-day turnaround for the first pass, aligning with your timeline. Are there any specific components or suppliers you prefer for the voltage regulators?

@shivisno1

I have 10 year experience in pcb designing and development used altium matlab Cadence kicad matlab tools to do full analysis and detailed work.

@keaganmini

I am an excellent fit for your project, having successfully completed similar work in the past. Your need for a compact, two-layer PCB focused on reliable power management with high-efficiency voltage regulators and strict DFM practices aligns perfectly with my expertise. I understand the importance of clean, professional, and user-friendly design that ensures seamless manufacturing via JLCPCB or PCBWay. I specialize in KiCad schematic capture, PCB layout, and generating complete manufacturing packages including Gerber files, drill files, and BOMs. Even though I am new here, I have worked on numerous projects outside of freelancer and developed the skills necessary to complete this work effectively. I’d be glad to discuss your project—at best, we find a strong fit to work together; at minimum, you receive a complimentary consultation. Regards, Keagan

@Vsion2

Hi there, I'm Alema, I can do the task perfectly and professionally please message me for a detailed discussion. I have completed 300+ projects with a 100% Positive Rating, If you are looking for Quality work, look no further. We are always available 24/7 to help employers without limitations, and delivery is guaranteed on time. Thank you!

@wassimkroud

Compact two-layer power board within 60×40 mm is absolutely manageable. I can design the schematic in KiCad, select efficient low-noise regulators, and deliver a clean DRC/ERC-passed layout ready for JLCPCB/PCBWay. Thermal considerations, proper grounding, and regulator stability will be addressed from the start. Manufacturing files, 3D export, and structured BOM included. I can deliver first pass within 3 days. Let’s open a conversation and start immediately.