Prototypage rapide Jobs

We need a board that "translate" signal from DMX to led strip pixel adressable. Need to integrate RGB and RGBW pixel in various protocol, with clock or only data. Only one data signal needed (170 rgb pixel or 128 rgbw pixel to complete universe) -Possibilities to set start adress -Possibilities to control multiple pixel as one pixel (grouping for have total of 2x or 3x o 4x pixel controlled) -Setting IC ,Address and Grouping by dipswitch or other way accepted (also usb serial with proprietary software) -ALL SETTINGS NEED ALSO TO BE SETTED BY RDM -Usb or serial connector for upload firmware We are open to every system from arduino to anything. Need to be thinked in hardware and software side. Other this one we need a variant with pwm rgbw output with same feature like RDM, ...

I’m upgrading a vehicle with a roof-mounted thermal imaging camera and need a streamlined enclosure that behaves a bit like a transformer: it must rise, give the camera a full 180° pan and at least 30° of tilt, then fold back and disappear under a low-drag cover when not in use. The core of the job is mechanical design. I’m after a concept that can be built either by 3-D printing or injection-moulding, so please keep draft angles, wall thickness and other DFM considerations in mind from the outset. Weather sealing, vibration resistance and smooth airflow over the stowed housing are essential, but I’m flexible on the exact material as long as it can survive sun, rain and highway wind speeds. I need sourcing motors, sensors, circuitry, the enclosure geometry...

I’m ready to move an industrial-grade controller from concept to production and need a designer who has already shipped tight, 6-layer boards. The board must host a main microcontroller, its support circuitry, and several high-current power-regulator stages, all within a restricted outline while meeting EMI/EMC limits typical for factory environments. You’ll start from my block diagram and rough schematic notes, turn them into a production-ready layout, and supply every file the assembly house will ask for: updated schematics, stack-up, Gerbers, drill files, pick-and-place, BOM, and a brief design report explaining how the EMC strategy and size targets were achieved. I’ll be available for rapid feedback on component placement and routing choices, and we’ll sign ...

Description Of Project - HRID-AI is a low cost handheld device aimed at estimating ejection fraction using multimodal biosignals (ECG, seismocardiography, and cardiac acoustics). It uses a combination of biosensors to detect abnormalities in ECG, presence of abnormal heart sounds and their interpretation as well as usage of seismocardiographic signals to provide an estimate of Ejection Fraction. The principle has been verified through multiple studies done in reputed institutions The goal is rapid point-of-care triage for echo referral in emergency and low-resource settings in patients of Heart Failure with Reduced Ejection fraction We need your support, skills and expertise for sensor integration, embedded design, signal acquisition. Current Status- We have so far been able to dev...

Saya ingin sebuah video futsal berdurasi 60 detik yang terasa seperti trailer film olahraga: sinematik, berpola cerita, dan penuh emosi. Saya belum memiliki bahan mentah, jadi Anda perlu datang ke lapangan (Jakarta) untuk mengambil rekaman baru—mulai dari arrival tim, briefing strategi, hingga aksi di lapangan. Fokus utama saya adalah menonjolkan kerjasama tim dan strategi. Saya membayangkan alur singkat: build-up ruang ganti, cuplikan passing cepat, close-up ekspresi pemain, lalu klimaks selebrasi kemenangan. Transisi halus, color grading bergaya teal-orange, sound design dramatis, dan scoring musik yang membangun tensi akan sangat membantu menghadirkan nuansa film. Deliverable: • 1 video final 1 menit, resolusi 1080p & 4K • File project mentah (Premiere Pro/DaVinc...

I have a component supplied only as a 3DPDF. First, I need that file properly converted to a clean, watertight STL. Once the geometry is in STL form, I want to open it in SolidWorks and carry out two key changes: add a couple of functional features of my own and merge the whole piece so it mates perfectly with another part I will supply in STL format. Dimensional accuracy at the interface is critical because these two parts will eventually form a single molded assembly. After the digital work is done, I’d like a short prototype run—just enough 3-D-printed samples for a quick fit-check and functional assessment before we move on to tool design for injection molding. Fast turnaround is important; I’m aiming to review the modified files and receive the print samples as soon...

Description Of Project - HRID-AI is a low cost handheld device aimed at estimating ejection fraction using multimodal biosignals (ECG, seismocardiography, and cardiac acoustics). It uses a combination of biosensors to detect abnormalities in ECG, presence of abnormal heart sounds and their interpretation as well as usage of seismocardiographic signals to provide an estimate of Ejection Fraction. The principle has been verified through multiple studies done in reputed institutions The goal is rapid point-of-care triage for echo referral in emergency and low-resource settings in patients of Heart Failure with Reduced Ejection fraction We need your support, skills and expertise for sensor integration, embedded design, signal acquisition. Current Status- We have so far been able to dev...