Hardware Engineers à embaucher
Montrer 4 résultats
Freelances parrainés
-
I have more than 7 years experience in electrical engineering. I have expertise in three domains: Electronics Engineering: • Power electronics: DC DC converters, power supplies, AC DC, DC-AC power converter designing. Gate driver, switching circuit design. • Product Engineering: prototype development, product...I have more than 7 years experience in electrical engineering. I have expertise in three domains: Electronics Engineering: • Power electronics: DC DC converters, power supplies, AC DC, DC-AC power converter designing. Gate driver, switching circuit design. • Product Engineering: prototype development, product compliance and certification • SoC/SBC/USB/HDMI/Ethernet • NVidia Jetson/Raspberry Pi 4/CM4 • Microcontrollers(PIC, AVR, ARM, TMS320F, TI) • FPGAs, Digital Systems • Electronic Circuit Designs (Analog/Digital) • Power Electronics (High power DC-DC converters, Inverters) • Sensor designing and actuation • Battery management systems • Programming (MATLAB/Simulink, Verilog, C, C++) • Control Systems Engineering (Reactors, Boilers, Motors) • Software/Mathematical Simulations (MATLAB, Multisim) Solar Design Engineering: • Racking structural engineering for ground mount/roof mounting, and using PVSyst to determine azimuth and tilt angle for optimizing yield. • 2D and 3D Site layouts for rooftop/facades/ground mount solar sites considering shading/topology on the site. Module drawings/drafting from install manuals. • Stringing modules together, combiner box selection, inverter selection, and DC/AC cable selection. • Wiring/cable layout from the panels to electrical equipment to interconnection substation. • Electrical drawings; single line diagrams, three line diagrams and schematics. Power Systems Engineering: • Load Calculations, cable sizing, component selection, equipment and cable layout for power distribution. • Single Line Diagrams, Three Line Diagrams, schematics.. • Distribution Switchgear design schematics LT/HT upto 33kV • Relay coordination and Power System simulation using ETAP. • LUX calculations and Lighting design using DIALux. • MATLAB Simulink for alternate Energy Systems Simulations. moins
Embaucher Sherry1596
-
Analog / Mixed Signal / Digital, Arduino, Design de circuits, DDR3 (PCIe, board design/fpga), Design DigitalHave more than 10 years of Experience in Electronics Product Development, Developed High-Quality Electronics Products. Developed below mentioned Products 1. Video Processing Board (Using Xilinx FPGA, Intel FPGA and Microsemi FPGA) 2. Network Switch Board (Using Xilinx FPGA, Intel FPGA and Microsemi FPGA) 3. Radar...Have more than 10 years of Experience in Electronics Product Development, Developed High-Quality Electronics Products. Developed below mentioned Products 1. Video Processing Board (Using Xilinx FPGA, Intel FPGA and Microsemi FPGA) 2. Network Switch Board (Using Xilinx FPGA, Intel FPGA and Microsemi FPGA) 3. Radar Processing Board (Using Xilinx FPGA, Intel FPGA and Microsemi FPGA) 4. Signal Processing Board (Using DSP Processor) 5. Air Quality Monitor (ESP32 based) 6. Radar Receiver Card (L-Band, S-Band, C-Band, X-Band, Ku-Band and K-Band) 7. RF Transceiver Board (L-Band, S-Band, C-Band, X-Band, Ku-Band and K-Band) 8. RF Up/Down Converter (L-Band, S-Band, C-Band, X-Band, Ku-Band and K-Band) moins
Embaucher kktroops90
-
Hello, Thanks for taking the time to review my profile! I’m an Electronics Engineer specializing in PCB and Electronics Design. With years of experience in the industry, I’ve built my business as a freelancer around being detail-oriented, punctual, and innovative whenever possible. I believe in providing my clients...Hello, Thanks for taking the time to review my profile! I’m an Electronics Engineer specializing in PCB and Electronics Design. With years of experience in the industry, I’ve built my business as a freelancer around being detail-oriented, punctual, and innovative whenever possible. I believe in providing my clients with the best possible product without breaking the bank. I offer services in many areas, including (but not limited to): ● Embedded Systems: Analog and digital circuitry design and simulation, PCB design, firmware development. ● Analog Electronics Design: Analog frontends, amplifiers, filters, mixers, and general analog circuitry for low-frequency, low-power precision applications. ● Power Electronics: Circuitry design and simulations, high power PCB design, control systems. ● RF design: RF circuitry and PCB design. I offer services for all product development stages: Proof of Concept, Prototyping, Value Analysis and Value Engineering, and Product Release. I’m well-versed in a vast array of software and tools, and believe in always keeping up to date on the most modern and revolutionary techniques. I am proficient in: ● Schematic drawing and PCB design: Altium Designer, KiCAD and EagleCAD. ● Software simulation: NGSpice, PSpice and LTSpice. ● Firmware development: STMcube (ST Microelectronics), CCS (Texas Instruments), Segger Embedded Studio and MPLABX (Microchip and Atmel). If you’re interested in working with me, I’m available via Freelancer and will always answer your questions or requests in a timely manner. Thank you for your time and have a great day! moins
Embaucher cmsivolella
-
Hi, I'm an Electronic Engineer, also I'm a PhD—student in Multimedia and Communications. I have 6 years of work experience in the following fields: - Analysis, design, implementation, and verification of the Electronic design. - FPGA developer, using VHDL programing language. - Investigation and research. -...Hi, I'm an Electronic Engineer, also I'm a PhD—student in Multimedia and Communications. I have 6 years of work experience in the following fields: - Analysis, design, implementation, and verification of the Electronic design. - FPGA developer, using VHDL programing language. - Investigation and research. - Documentation and analysis. - C, C++ programming using STM32 and microchip microcontrollers. idromidea.com moins
Embaucher adrianitanatali2
